Why does the pump surge in my Catalina LUXURY COLLECTION Hot Tub?
Pump surges in your Catalina Hot Tub can be caused by a water level that is too low (add water) or a blockage or restriction (empty the filter basket and clean the suction drain covers).
Why does my Catalina LUXURY COLLECTION Hot Tub heat, but not high enough?
If your Catalina Hot Tub heats, but not to the desired temperature, it could be due to the thermostat being turned down (increase the temperature setting), a dirty filter (change the filter), a closed slice valve (open slice valves), or a shifted spa cover (reposition the spa cover).
How to fix cloudy water in my Catalina LUXURY COLLECTION Hot Tub?
Cloudy water in your Catalina Hot Tub can be due to several factors. You might need to replace the filter, add shock, or clean the cover with an approved cleaner. It could also be caused by improper sanitization or suspended organic matter, in which case you should add sanitizer. In some cases, you may need to clean or replace the filter, add shock, and run the jets. If the problem persists, consider draining and refilling the spa and replacing the filter, as the water may be at the end of its life or have a calcium pH imbalance.
What to do if I have skin irritation or rash after using my Catalina LUXURY COLLECTION?
If you experience skin irritation or a rash after using your Catalina Hot Tub, it could be due to several reasons: * Improper sanitation * Combined chlorine * Too much chlorine * A dirty filter * pH imbalance Test the water and add shock and sanitizer as needed. Adding water to lower sanitizer levels may also help. Clean or replace the filter to resolve this issue.
Why does my Catalina LUXURY COLLECTION Hot Tub water have a bad smell?
A bad smell in your Catalina Hot Tub water can be caused by excessive organic matter, bacteria growth, improper sanitization, low pH, or chloramines. To address this, add shock, sanitizer, adjust the pH, or add oxidizing shock.
Why will my Catalina LUXURY COLLECTION not power off?
If your Catalina Hot Tub will not power off, it may be because the spa is heating or filtering, which is a normal function. Try lowering the temperature settings.
Why is the GFCI tripping on my Catalina Hot Tub?
If the GFCI is tripping on your Catalina Hot Tub, it is likely due to improper wiring. Have an electrician check the neutral wiring connections at the GFCI.
Why is my Catalina Hot Tub leaking?
If your Catalina Hot Tub is leaking, it could be due to loose unions. Hand tighten the unions to resolve this.
How to remove stains on the acrylic surface of my Catalina Hot Tub?
Stains on the acrylic surface of your Catalina Hot Tub can be caused by high alkalinity or low pH (adjust alkalinity and pH accordingly), high mineral content (use stain & scale reducer), high metal content (use metal sequestering agent), or high calcium levels (adjust alkalinity and use stain and scale reducer).
Why is the water flow low in my Catalina LUXURY COLLECTION?
Low water flow in your Catalina Hot Tub can occur because the spa is heating or filtering (normal spa function), the diverter valve position (rotate diverter valve to increase flow), the air valve is closed (rotate air valve to open), the filter is dirty (clean or replace filter), the slice valve(s) are closed (open slice valves), or there is improper line voltage (have an electrician check voltage).
Ensures electrical connections are made by a licensed electrician and GFCI is used.
Emphasizes supervision and safety measures to prevent unauthorized child access.
Warns against loose clothing, hair, or jewelry near moving parts and suction fittings.
Details requirements for concrete pads, drainage, and clearances for outdoor spa installation.
Covers floor load capacity, drainage, and ventilation for indoor spa installations.
Steps and considerations for receiving and safely unloading the spa.
Instructions on ensuring the spa is perfectly level after positioning for proper operation.
Details safety precautions and installation requirements for 240V spa power connections.
Specifies wire size, breaker type, and connection methods for 240V spa systems.
Guidelines for qualified electricians on 240V spa wiring and GFCI installation.
Covers the specific requirements and safety for 120V spa power connections.
Highlights the critical role of correct GFCI installation for safety and component protection.
Illustrates the wiring connections for a Midwest Brand 50 AMP GFCI for 220V spas.
Provides wiring diagram and installation details for the Eaton Brand 50 AMP GFCI.
Illustrates the wiring connections for the Square D 50 AMP GFCI for 220V spa systems.
To Next Page
General
