cecotec POWER ESPRESSO User Manual

POWER ESPRESSOPOWER ESPRESSO
3938
ENGLISH ENGLISH
water as follows:
- Pour water into the water tank, the water level should not exceed the “MAX” mark in the
tank. Close the water-tank cover.
Note
The appliance is equipped with a detachable water tank for easy cleaning. Fill the tank with
water rst and put it back inside the device.
- Insert the stainless-steel lter into the portalter without ground coee. Then, insert the
portalter into the appliance, matching the shape of the lter holder and the shape of the
water outlet. Turn it counterclockwise until the handle is aligned with the “lock” mark on
the appliance.
- Place a jar on the removable grille. Make sure the steam knob is in the o position.
- Plug the device into a power supply. The plug must be accessible so that, in case of an
emergency, it can be easily unplugged.
- Press the Preheating-function button and the light indicator will start blinking. Wait until
the light indicator stops blinking.
- Press the coee button. The machine will pump water into the jug; press the button again
when the jug is full to stop the water. The light indicator will blink again until the product
stops preheating. Repeat this process twice.
Note
You may hear a noise when the appliance pumps water for the rst time. This is completely
normal, as air is being released inside the machine. After about 20 seconds, the noise will stop.
3. OPERATION
Preheating
- To prepare a cup of good hot espresso coee, it is recommended to preheat the appliance
before brewing coee, including the lter holder, lter, and cup to prevent avour from
being altered by cold parts.
- Remove the detachable tank, open the tank cover, and ll it with water. The water level
should not exceed the “MAX” mark in the tank. Install the tank back in the device.
- Insert the stainless-steel lter into the portalter. Then, insert the portalter into the
appliance, matching the shape of the lter holder and the shape of the water outlet. Turn it
counterclockwise until the handle is aligned with the “lock” mark on the appliance.
- Place an espresso cup on the removable grille.
- Plug the coee machine to a power supply. Make sure the steam knob is in the o position.
- Press the preheating-function button and the light indicator will start blinking. Wait until
the light indicator stops blinking.
1. PARTS AND COMPONENTS
Fig. 1.
1. Preheating-function button
2. Coee button
3. Steam button
4. Drip tray
5. Removable grille
6. Steam knob
7. Water-tank cover
8. Water tank
9. Housing
10. Steam outlet
11. Steam tube
12. Main body
13. Base
14. Single stainless-steel coee lter
15. Measuring spoon and tamper
16. Filter holder
17. Portalter
18. Filter fastener (press the lter with it when pouring out coee residue to prevent the lter
from slipping out)
19. Stainless-steel lter for two coees
NOTE:
The graphics in this manual are schematic representations and may not exactly match the
product.
2. BEFORE USE
- This appliance is packaged in a way as to protect it during transport. Take the appliance
out of its box and remove all packaging materials. You can keep the original box and other
packaging elements in a safe place. This will help you prevent product damage when
transporting it in the future. In case the original packaging is disposed of, make sure all
packaging materials are recycled accordingly.
- Make sure all parts and components are included and in good conditions. If any of them
are missing or not in good condition, please contact Cecotec’s ocial Technical Support
Service immediately.
- To ensure the rst cup of coee tastes excellent, you should rinse the coee machine with

cecotec POWER ESPRESSO Specifications

General

Type	Espresso Machine
Power	850 W
Milk Frother	Yes
Water Tank	Removable
Color	Black
Material	metal