4.
5.
1.
2.
3.
4.
5.
Be
careful
not
to
apply
voltage
I
DC
Volt
to
the
Test
Leads
Sel
ec
ti
on
when
they
are
Ar
ea
c o n n e c t e d .,
Ohm
t o t h e C 0 M
Selection
( B o
tt
o m ) a n d
Area
VOmA
(Center)
Jacks
and
the
!
Tran
s
istor
Multimeter
is
in
/hFE
Ja
ck
an
Ohms
testing
setting
.
Damage
can
occur
to
the
multimeter
or
the
fuse
may
blow
.
Do
not
switch
between
Control Layout
Battery
Test
.
Selection
Area
DC
AMP
Selection
Area
10A
Selection
Area/Jack
Transistor
Selection
Area
testing
modes
with
the
' '
VolUOhm/
multimeter
connected
to
a 1 [
mode
JI
COM
Jack
I
mA
Jack
Circuit. SAIA,-,trnn
Ar""
AC Voltage Measurements
Measure AC conductors
ca
rrying up to 750
VAC
, 45-450 Hz.
Turn the Range Selector Switch to 750 ACV setting.
Always start with the highest range if the voltage
is
unknown.
Plug the red lead into the
VOmA
(Center) Jack: Pl
ug
the black lead into
the COM (Bottom) Jack. Switch the
Mu
ltimeter ON.
Carefully touch the exposed conductors with the tips of the probes to measure
the voltage (not amperes).
Read measurement.
If the voltage is less than 200 vol\s, set the Range Selector Switch to the
lower range. .
I ·
When testing
is
complete, remove
Te
.st Leads and store with multimeter.
I
J
!I
DC Voltage Measurements
Measure.
DC
conductors
cr
rrying up to 1000 VDC.
1. Turn the Range Selector Switch
to
1000 DCY setting.
2. Follow the directions above under "AC .Voltage Measurements", only use
the
DC
settings instead.
SKU 69096
For replacement parts, please call 1-800-444-3353.
Page 5
1.
2.
3.
DC Current Measurements
Measure
DC
conductors c
'\
rrying up to
10
ampere
s.
Turn the Range Selector Switch to the 10A position. .
Always start with the highest range if the amperage
is
unknown.
Plug the red lead into the 1
OA
(Top)
Jack. Plug the black lead into the COM
(Bottom) Jack. Switch the Multimeter
ON
.
Carefully touch
the
exposed conductors with the tips of the probes to measure
the amperage.
Note: Amperage
is
always tested
in
series with the circuit under test.
4. Read measurement.
If the reading is less than .2AMPs, switch the req lead
to
the VOmA(Center)
Jack and set the Range Selector Switch to the 200 mA setting.
5. When testing is complete, remove Test Leads
and
store with multimeter.
Resistance Measurements
Measure circuit resistance up to 2000K Ohms.
l
WARNING: NEVER measure resistance
on
a circuit with voltage running
through
it.
· j
1.
=Turn
the Range Selector
Switc;h
to the 200 mA position.
2. Plug the red Test Lead into the
VOmA
(Center) Jack. Plug the black Test
Lead into the Com (Bottom) Jack. Switch the Multimeter
ON
.
3.
4.
1.
2.
3.
1.
2.
Short the Test Leads together. The meter should read "O" Ohms.
Touch the exposed conductors
wi
th the tips of the Test Leads.
Read measurement.
I
If the readi
ng
is "1
",set
the Rang
ei
Selector Switch to the next higher Ohm
(0)
position.
Transistor (hFE)!Measurements
Test
transistors to ensure proper function.
Turn the Range Selector Switch
t
~
the hFE position.
Switch the Multimeter
ON
.
Insert
the transistor pins into
th
13
appropriate hFE jack (NPN or PNP)
according to the EBC (Emitter, Base, Collector) sequence.
The meter will show the approximate hFE value. ,
Diode Measurement
Test the voltage drop
in
diodes.
Turn the Range Selector Switch to the Diode ( ...... ) position. \
Pl
ug
the red Test Lead into the V1
0mA
(Center) Jack. Pl
ug
the black
~
est
Lead into the Com (Bottom) Jack. Switch the Multimeter
ON
. .
3. Connect the
red
probe to the anode of the diode
and
the black to the cathode.
SKU 69096
For replacement parts, please call 1-800-444-3353. Page 6
To Next Page
Loading...
Need help?
General
