4
Clearing CD Memory
After the playing of programmed track stops, press STOP again to
clear the memory. MEMORY on the display disappears.
TUNER OPERATION
To switch to the tuner mode from the CD mode, press TUNER
BAND until AM or FM appears on the display.
At FM band, repeatedly press ST/MONO to select the stereo or
mono sound as you desire. STEREO or MONO appears on the
display.
Tuning
Manual searching—Repeatedly press F or J to search the
frequency.
Automatic searching — Hold the F or J for over half a second
then release to search the frequency. The frequency on the
display will run to search and will stop when it receives a strong
signal.
Memory search — Press the number buttons on the remote
control to select the preset channel directly.
Or, you can repeatedly press REPEAT M-UP to search the preset
channel.
PRESET THE RADIO CHANNEL
You can store up to 20 FM stations and 12 AM station in memory.
1. Repeatedly press TUNER BAND to select the desired band.
Note: Select one method to search the channel as you like.
2. Press CL/MEM on the remote control or MEM/CLOCK on the
CD player. When the desired channel is received, CH
appears and -- beside the frequency flashes.
3. Within 5 seconds press the digit button on the remote control
or press REPEAT M-UP on CD player or CL/MEM on the
remote control to confirm your presetting.
4. Repeat step 2 and step 3 to preset the other channels.
5. You can press the number buttons on the remote control to
select the programmed channels. Or repeatedly press
REPEAT or REPEAT M-UP to search for the channel
programmed.
SETTING THE CLOCK
1. Press POWER button to turn the unit off.
2. Press MEM/CLCOK on the main unit or CL/MEM on the
remote control, the hour digit flashes on the display.
3. Repeatedly press or hold J or F to change the hour digit to
your desired setting.
4. Press MEM/CLOCK or CL/MEM with the minute digit
flashing.
5. Repeatedly press or hold J or F to change the minute digit
to your desired setting.
6. Press MEM/CLOCK or CL/MEM to confirm you setting.
To see the clock when CD player is playing, press MODE until the
time appears.
USING THE TIMER
Note: You need to set the time before setting the timer.
You can set a time as TIMER ON or TIMER OFF to turn on or off
the CD player automatically as desired.
The timer turns on automatically after you set it. To turn off the
timer, repeatedly press MODE on the remote control until TIMER
OFF appears on the display.
Note: In any mode you can turn the timer on/off. When you turn
both of them on, TIMER ON OFF appears on the display. When
you turn one of them on TIMER ON or TIMER OFF appears.
When you turn them off, TIMER ON OFF disappears.
SETTING TIMER ON
1. Repeatedly press MODE on the remote control until TIMER
ON flashes on the display.
2. Press MEM/CLOCK on the main unit or CL/MEM on the
remote control, the hour digit flashes on the display.
3. Repeatedly press or hold J or F to change the hour digit to
your desired setting.
4. Press MEM/CLOCK or CL/MEM with the minute digit
flashing.
5. Repeatedly press or hold J or F to change the minute digit
to your desired setting.
6. Press MEM/CLOCK or CL/MEM to confirm your
setting. ON steadily appears on the display.
Note: The CD player will play the last program you listened to
when it turns on at your set time.
SETTING TIMER OFF
1. Repeatedly press MODE on the remote control until TIMER
OFF flashes on the display.
2. Press MEM/CLOCK on the main unit or CL/MEM on the
remote control, the hour digit flashes on the display.
3. Repeatedly press or hold J or F to change the hour digit to
your desired setting.
4. Press MEM/CLOCK or CL/MEM with the minute digit
flashing.
5. Repeatedly press or hold J or F to change the minute digit
to your desired setting.
6. Press MEM/CLOCK or CL/MEM to confirm your
setting. OFF steadily appears on the display.
CD CARE TIPS
Even though a compact disc is durable, treat the CD surface with
care.
• Do not write on either side of the CD, particularly the non-
label side (signals are read from the non-label side).
• Do not store CDs in high temperature of high humidity areas.
They might warp.
• Keep CDs dry. A water drop can act as a lens and affect the
laser beam’s focus.
Always handle a CD by the edges to avoid fingerprints and always
keep in it in its protective case or sleeve when it is not in use.
Fingerprints and scratches on the CD’s surface can prevent the
laser beam from correctly reading the digital information.
CONNECTING WITH AUXILIARY
EQUIPMENT
You can connect other audio equipment to use the CD player as a
speaker system.
1. Using a stereo connection cable (not supplied),connect AUX
IN Jack on rear of the CD player to AUX OUT Jack on
another audio device.
2. Press AUX button to enter AUX mode.
3. Play the connected audio device according to its instruction
manual.
To Next Page
Loading...