Ceragon FibeAir 1500HP Installation Guide

178 pages

To Next Page

FibeAir

1500HP/RFU-HP

Installation Guide

Part ID: BM-0111-0

Doc ID: DOC-00015514 Rev C

March 2015

Default Chapter3
- Table of Contents3
1 About this Guide7
2 What You Should Know7
3 Target Audience7
4 Related Documents7
5 Important Notes8
6 HP/RFU-HP Models and Part Numbers9
7 Fibeair 1500HP/RFU-HP Ocbs11
- OCB Components12
8 Split-Mount Installation with the OCB13
- Required Tools for the OCB Installation13
- Special Tools/Materials13
- Pole Mount Preliminary Assembly14
- Installing Couplers15
- Installing S-Bends and the DCB16
- Short Installation17
- Termination Installation18
- Short with Tapped Holes Installation19
9 Final Branching Installation20
10 Connecting the RFU to the OCB21
11 Housing Assembly and Lifting Harness22
12 Pole Installation23
13 Hanging Positions24
14 Outdoor Branching Network (OBM) Housing Hanging Procedure25
15 Connecting a Flexible Waveguide26
16 RFU Cable Connections27
17 Grounding the 1500HP/RFU-HP29
18 Installation Instructions for Specific Configurations30
- 1+0 Sd33
- 1+1 Sd35
- 1+1 Hsb39
- 2+0 Dp42
- 2+0 Sp45
- 2+0 Sd Sp48
- 2+0 Sd Dp51
- 2+2 Sd Sp54
- 2+2 SD DP (Non-Upgradable)65
- 2+2 HSB DP (Ready for Upgrade)70
- 2+2 HSB DP (Non-Upgradable)74
- 2+2 Hsb Sp78
19 Upgrade Instructions84
- Upgrading from 1+1 SD to 2+2 SD SP84
- Upgrading from 1+1 HSB SP to 2+2 HSB SP96
- Upgrading from 2+2 DP to 3+3 DP103
- Upgrading from 2+2 SD SP to 3+3 SD SP107
- Upgrading from 2+2 SD DP to 3+3 SD DP119
- Upgrading from 2+2 HSB SP to 3+3 HSB SP123
- Upgrading from 3+3 DP to 4+4 DP130
- Upgrading from 3+3 SD DP to 4+4 SD DP135
- Upgrading from 3+3 SD SP to 4+4 SD SP140
- Upgrading from 3+3 HSB SP to 4+4 HSB SP144
20 Split Trunk Configurations149
- 1+1/2+2 HSB Configurations149
- N+0/N+1 Single Pole Configurations (N = 1 to 5)150
- N+0/N+1 CCDP Configurations (N = 1 to 5)152
- N+0/N+1 CCDP Configurations (N = 5 to 10)154
21 All Indoor Horizontal Installation157
- 1+0 Installation158
- Parts Used158
- Assembly158
- 1+0 East-West Installation161
- Parts Used161
- Assembly161
- 1+1 HSB (Hot Standby) Installation164
- Parts Used164
- Assembly164
22 Appendix A: Electrical Diagrams167

Other manuals for Ceragon FibeAir 1500HP

Installation And Operation Manual257 pages

Questions and Answers:

T
Tracy GarnerSep 13, 2025
How to resolve insufficient system configuration for full XPIC support on Ceragon Antenna?
- W
  William RuizSep 13, 2025
  If your Ceragon Antenna system configuration is insufficient for full XPIC support, it could be due to a missing or unsupported system element. To resolve this: 1) Verify the existence of all IDMs and ODUs, and confirm their connectivity. 2) Open the unit Alarm Log using the element manager and send the "XPIC Insufficient" event code to customer support.