Need help?Do you have a question about the CHAFFOTEAUX PIGMA Gal Evo and is the answer not in the manual?
General| Brand | CHAFFOTEAUX |
|---|---|
| Model | PIGMA Gal Evo |
| Category | Boiler |
| Language | English |
Provides dimensions and physical layout of the boiler unit.
Visual diagram showing internal components of the sealed chamber boiler.
Details the control board, buttons, and display functions for user interaction.
Explains display icons and operating mode indications on the boiler screen.
Explains how the boiler functions in heating mode, including component operation.
Details the boiler's operation for domestic hot water production.
Function for boiler combustion analysis and gas calibration.
Allows user to activate temperature holding in the sanitary water reserve tank.
Protects the boiler from freezing by activating pump and burner under specific temperature conditions.
Monitors water flow and triggers safety shutdowns based on temperature gradients.
Helps purge residual air from the primary circuit after a filling cycle.
Adjusts heating restart delay based on operating conditions or user settings.
Describes the right-side composite hydraulic block with integrated functions.
Details the left-side composite hydraulic module for CH and domestic hot water.
Explains the 3-way valve, its motor, and its operation in heating and sanitary modes.
Describes the sanitary plate heat exchanger and its role in heat exchange.
Details the pump unit, its types, speeds, and modulation capabilities.
Explains how to drain the primary circuit using the drain port and plug.
Describes the automatic bypass valve and its function in ensuring minimum flow rate.
Details the primary heat exchanger, its material, and function in heat transfer.
Explains the function of pressure pick-ups for monitoring primary circuit pressure.
Describes the heating line filter and instructions for cleaning it.
Details the heating expansion vessel's technical specifications and capacity.
Explains the sanitary flow meter operation and its role in initiating ignition sequences.
Describes the temperature sensors (NTC1, NTC2) and their resistance values.
Details the SIT 845 SIGMA gas valve, its features, and control capabilities.
Provides the electronic connection diagram for the solenoid gas valve.
Covers checks and adjustments for gas supply pressure, maximum/minimum power, and ignition.
Procedure for checking the gas supply pressure at the inlet.
Procedure to check and adjust the maximum power output for sanitary hot water.
Procedure to check and adjust the minimum power output for heating and sanitary.
How to check and set the power level for soft ignition.
Setting the delay time between burner shutdown and re-ignition for heating.
Adjusting the maximum heating power using parameter 230 and 231.
Table detailing gas properties and burner jet specifications for different gas types.
Describes the burner assembly, its technology, and nozzle diameters.
Details the flue exhaust ports for combustion analysis and pressure switch testing.
Explains the air pressure switch function for checking vacuum and extractor operation.
Details the extractor's technical data and its role in the ventilation system.
Describes different post-ventilation cycles based on operating conditions and faults.
Explains the SPOTT unit's role in controlling flue stack draft and its thermal contact function.
Details the flue exhaust system for CF models, including anti-return devices and regulations.
Illustrates exhaust system configurations for coaxial and twin pipe setups.
Describes the GAL2EVO ATM main electronic card and its protective features.
Shows the electrical connections and layout of the main electronic PCB.
Provides the electronic diagram for the FF boiler's control board and peripherals.
Provides the electronic diagram for the CF boiler's control board and peripherals.
Guides the user on navigating and adjusting boiler parameters via the menu system.
Presents a comprehensive list of all menu parameters, their ranges, and default settings.
Network configuration and status information for the boiler's bus connection.
Settings related to general boiler functions, heating, and hot water.
Configuration parameters for heating zone 1, including setpoints and thermoregulation.
Configuration parameters for heating zone 2, including setpoints and thermoregulation.
Configuration parameters for heating zone 3, including setpoints and thermoregulation.
Access to service parameters, diagnostics, maintenance, and error history.
Explains the types of errors, their codes, and reset procedures for boiler malfunctions.
Specifies annual checks for the sanitary heat exchanger, focusing on Delta T.
Outlines annual visual checks for the bypass and 3-way valve for aspect and property.
Specifies annual visual checks for the heating filter for aspect and property.
Specifies annual checks for the expansion vessel, including inflating pressure.
Details annual checks for the sanitary flowmeter, including start-up flow rate and visual aspect.
Specifies annual checks for ignition and ionization sensors, including distance and current.
Outlines annual visual checks for the burner and supply tank for aspect, property, and flame outline.
Details annual checks for the air pressure switch, including DP measurement.
Specifies annual checks for the extractor, focusing on visual aspect, property, and turbine.
Outlines annual visual checks for the exchanger for aspect and property.
Provides technical specifications for the PIGMA CF model, including performance and electrical data.
Provides technical specifications for the PIGMA FF model, including performance and electrical data.
To Next Page