3.17.22 ISO 11783 Class 3 ................................................ 1
18
3.17.23 Service intervals ................................................. 119
3.17.24 Headland management ............................................ 123
3.17.25 Headland management icon identification ............................... 126
3.17.26 DTC (diagnostic trouble codes) stored or active ........................... 128
3.17.27 Track tension ....................................................129
3.17.28 3-point linkage ...................................................130
3.17.29 Slip calibration ................................................... 132
3.17.30 Steering calibration ............................................... 134
3.17.31 Inching pedal calibration ............................................136
3.17.32 Radar calibration ................................................. 137
3.17.33 Enable the video camera - software version 3.2 and before .................. 139
3.18 Air system operation ............................................... 140
3.18.1 Air trailer brake couplers ........................................... 140
3.18.2 Air hose connection ...............................................141
3.19 Machine control ....................................................142
3.19.1 Throttle control .................................................. 142
3.19.2 Decelerator - if equipped ........................................... 142
3.19.3 Power management .............................................. 142
3.19.4 Brake control ....................................................143
3.19.5 Service brakes .................................................. 143
3.19.6 Hydraulic trailer brake if equipped ..................................... 144
3.19.7 Park brake ......................................................144
3.19.8 Manual parking brake handle ........................................ 145
3.20 Overweight protection strategy (OWPS) ............................ 146
3.21 Inching pedal control ............................................... 147
3.22 Transmission ...................................................... 148
3.22.1 Transmission control .............................................. 148
3.22.2 Machine ground speeds ........................................... 148
3.22.3 Ground speeds for creeper transmission ............................... 149
3.22.4 Creeper gear .................................................... 149
3.22.5 Transmission control lever .......................................... 150
3.22.6 Transmission shifting diagram ....................................... 151
3.22.7 Preselect a gear before you move .................................... 151
3.22.8 Use of the inching clutch control ..................................... 151
3.22.9 Operate the shuttle shift ........................................... 151
3.22.10 Speed match ................................................... 152
3.23 Hydraulic controls .................................................. 153
3.23.1 Hydraulic control valve operation ..................................... 153
3.23.2 Roading lockout switch for the hydraulic control levers ..................... 155
3.24 General hydraulic connections ...................................... 156
3.24.1 Connect hoses to the quick couplers .................................. 156
3.24.2 Disconnect hoses from the quick couplers .............................. 157
3.24.3 Hydraulic flow management ........................................ 157
3.24.4 Hydraulic motors ................................................. 157
3.24.5 Selection of hydraulic motors ........................................ 157
3.24.6 Single acting cylinders ............................................. 158
3.24.7 Connect a double acting cylinder ..................................... 158
3.24.8 Connect hydraulic motors to the control valves ........................... 158
3.24.9 Connect the hydraulic motor with the flow control valve .................... 159
3.24.10 Connect a grain cart with an auger motor ............................... 159
3.24.11 Semi - mounted vacuum planter with the lift assist wheels .................. 161
3.24.12 Connect the vacuum planter ........................................ 161
3.24.13 Connect the air seeder or the grain drill ................................ 162
3.24.14 Connect the auxiliary implement controls ............................... 164
3.24.15 Connect the spray system pump ..................................... 164
3.24.16 Connect a hydraulic motor to power beyond ............................. 164
Table of contents
Rubber Track Tractor
5640
01D1E
Find manuals at https://best-manuals.com