Instructions are Described and Illustrated Below
1. Press and release the “learn” button
on the motor unit. The learn indicator
light will glow steadily for 30 seconds.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit
light blinks. It has learned the code. If light
bulbs are not installed, two clicks will be
heard.
To Erase All Codes From Motor Unit Memory
To deactivate any unwanted remote, first erase all codes:
Press and hold the “learn” button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous
codes are now erased. Reprogram each
remote or keyless entry you wish to use.
To Control the Opener Lights
With Security✚ transmitters, a remote push button can
be programmed to operate the opener lights without opening
the door.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
To prevent possible SERIOUS INJURY or DEATH from a moving gate
or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
© 2002, Chamberlain Group Inc.
114A2210D All Rights Reserved Printed in Mexico
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
US: 1-800-528-2817
CANADA: 1-800-654-4736
Open/Close/Stop Operation
Your Security✚ remote control can be programmed to operate
one door using all 3 buttons: the large button will only open the
door, the middle button will close the door, and the third button
will stop the door’s movement .You may set up this feature as
follows:
1. With the door closed, press and hold the
large remote push button.
2. Press and hold the Lock button on the
door control.
3. Press and hold the door control push bar.
When the opener lights flash, release all buttons. Test by
pressing the large (Open) button on the remote. The door should
open. Press it again while the door is open and nothing should
happen. Press the middle (Close) button while the door is
moving and it should close. Press the third (Stop) button and the
door should stop immediately.
The Remote Control Batteries
The lithium batteries should produce power
for up to 5 years. To replace, pry open case
with visor clip or screwdriver, as shown.
Insert batteries positive side up (+).
Dispose of old batteries properly.
Replacement Parts
Model 973LM Security✚ remote case
(circuit board not included): . . . . . . . . . . . . . . . . . . .41A5056-3
3V2032 Lithium battery: . . . . . . . . . . . . . . . . . . . . . . . . . .10A20
Visor clip: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29B137
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.