Champion M2 Series Installation Guide

6-1/16"
[154]
4-13/16"
[122]
6-7/8"
[175]
18-7/16"
[469]
5-3/4"
[146]
25-3/8"
[645]
Inside Table
Flange
26-7/8"
[683]
5-3/4"
[145]
Min.
Clearance
Door Interlock
4-11/16"
[119]
5"
[128]
96-3/4"
[2458]
27"
[686]
26-1/8"
[664]
7-1/4"
[184]
31-5/8"
[804]
60"
[1524]
8-5/16"
[212]
22-1/16"
[560]
Rinse Aid
Injection
1/8" NPT
Detergent
Injection
7/8" DIA
Detergent
Probe
7/8" DIA
79"
[2007]
3-9/16"
[91]
8-9/16"
[217]
33-15/16"
[862]
6-1/4"
[159]
4-7/16"
[112]
19-1/2"
[496]
11-5/16"
[288]
DH6000T-VHR
with Ventless Heat-Recovery and Condensate
Removal
Shipping weight crated: 350 lbs.
Dimensions shown in inches and [mm]
6-1/16"
[154]
4-13/16"
[122]
6-7/8"
[175]
18-7/16"
[469]
5-3/4"
[146]
25-3/8"
[645]
Inside Table
Flange
26-7/8"
[683]
5-3/4"
[145]
Min.
Clearance
Door Interlock
4-11/16"
[119]
5"
[128]
96-3/4"
[2458]
27"
[686]
26-1/8"
[664]
7-1/4"
[184]
31-5/8"
[804]
60"
[1524]
8-5/16"
[212]
22-1/16"
[560]
Rinse Aid
Injection
1/8" NPT
Detergent
Injection
7/8" DIA
Detergent
Probe
7/8" DIA
79"
[2007]
3-9/16"
[91]
8-9/16"
[217]
33-15/16"
[862]
6-1/4"
[159]
4-7/16"
[112]
19-1/2"
[496]
11-5/16"
[288]
Plan View
SPECIFICATIONS
Capacities
Racks per hr. (NSF rated) 40
Wash tank (gal.) 10
Motor horsepower 2 HP
Water consumption
Gal. per hr. 29
Gal. per rack 0.73
Temperature °F
Wash 150
Rinse 180
Heating
Tank heat, electric 5.2 kW
Electric Booster 7.5 kW
Dish-
washer
Mode
Pot &
Pan
Mode
Selectable cycle
times in minutes
1 246
Time cycles in seconds
Wash 36 94 214 334
Rinse 8 10 10 10
Sanitary Dwell 16 16 16 16
Vent Fan 30 30 30 30
Total 90 150 270 390
Warning: Plumbing, electrical connections should be
made by qualified personnel who will observe all the
applicable plumbing, sanitary and safety codes and the
National Electrical Code.
Note: Optional Drain Tempering: 1/2” NPT cold water
connection required. 1/2” NPT drain connection from back flow
preventer to house drain. (FIELD INSTALLED and PLUMBED).
Note: Water Hammer Arrestor (meeting ASSE-1010 standard or equivalent)
to be supplied (by others) in common water supply line at service connection.
UTILITIES
1 Electrical Machine Connection
(See Electrical Box)
2 Cold Water 3/4" NPT Cold Water 50° - 75°F
45 PSI Min Incoming (20-22 PSI flow)
3 Drain 1.5" OD Connection; 15 GPM Max
Flow (Drain water tempering height 5")
4 Drain Water Tempering 1/2" Cold water
line with customer supplied cut-off valve
(optional)
5 Integrated Detergent System Detergent
bottle supply connections (optional)
Due to an ongoing value analysis program at
Champion, specifications contained in this catalog
are subject to change without notice.
Champion Industries, Inc.,
3765 Champion Blvd., NC 27105
336/661-1556 • Fax: 336/661-1979
ChampionIndustries.com
Machine & Built-in Booster (Standard)
Voltage
Rated
Amps
Minimum Supply
Circuit Ampacity
Maximum
Overcurrent
Protective Device
208-240/60/1 77-68 100 100
208-240/60/3 46-41 60 60
480/60/3 20 30 30
Machine Only
(two point
electrical connection
)
Voltage
Rated
Amps
Minimum
Supply Circuit
Ampacity
Maximum
Overcurrent
Protective Device
208-240/60/1 38-34 50 50
208-240/60/3 25-23 30 30
480/60/3 11 15 15
Booster Only (two point electrical connection)
Voltage
Rated
Amps
Minimum
Supply Circuit
Ampacity
Maximum
Overcurrent
Protective Device
208-240/60/1 39-34 50 50
208-240/60/3 21-18 25 25
480/60/3 9 15 15
Detergent
Injection
7/8" Dia
Detergent
Probe
7/8" Dia
Rinse Aid
Injection
1/8" NPT
Rinse
Pressure
Gauge
8-5/16"
[212]
33-5/8"
[853]
8-9/16"
[217]
6-1/4"
[159]
4-7/16"
[112]
19-1/2"
[496]
34-1/8"
[866]
26-7/8"
[683]
6-1/16"
[154]
25-3/8"
[645]
Inside Table
Flange
5-3/4"
[146]
4-13/16"
[122]
6-7/8"
[175]
18-7/16"
[469]
6" [152]
to Inside
Tank Wall
8-1/8" [207]
to Rack
Guide
64-5/16"
[1634]
68"
[1727]
48-7/8"
[1242]
7-1/4"
[184]
31-5/8"
[804]
4-11/16"
[119]
5-3/4"
[145]
Min
Clearance
15-5/16"
[389]
3-1/16"
[78]
3-9/16"
[91]
11-5/16"
[288]
Corner Table
Configuration
Typical Table Construction
[762]
30"
1-1/2" [32] Roll
1-1/8"
[29]
7-1/4" [184]
21-3/8"
[543]
69-3/4"
[1770]
29-1/2"
[749]
4-3/8"
[112]
14-1/8"
[359]
19-5/8"
[500]
26-1/8"
[663]
8-3/4"
[224]
60-1/8"
[1526]
37-7/8"
[963]
33-3/4"
[857]
8"
[203]
6"
[152]
4-3/4"
[122]
8-3/4"
[221]
17"
[432]
8-7/8"
[225]
31"
[787]
34-1/8"
[867]
3-7/8"
[97]
41-3/8"
[1052]
18-1/8"
[549]
77-1/4"
[1963]
Hood
Up
17"
[431]
Clearance
7-5/8"
[192]
From
Wall
20-1/8"
[511]
INSIDE TRACKS
5-1/8"
[129]
3/8"
[9]
30"
[764]
Table
Typ
30"
[762]
26-1/2"
[673]
21-3/8"
[543]
1-1/2"
[38]
25-1/4"
[641]
Between
Tables
20-1/8"
[511]
8-3/8"
[214]
From Wall
INSIDE TRACKS
Specification Sheet
v

Champion M2 Series Specifications

General

Brand	Champion
Model	M2 Series
Category	Dishwasher
Language	English