Champion UH-200 User Manual (English)

Other manuals for Champion UH-200

Technical Manual175 pages

Installation & Operation Manual106 pages

Installation/Operation Manual With Service Replacement Parts106 pages

Questions and Answers:

V
Vanessa JonesAug 16, 2025
Why does my Champion UH-200 have poor wash results?
- J
  Jeremiah LawrenceAug 16, 2025
  Poor wash results with your Champion Dishwasher can stem from several issues. It could be due to low water temperature, which requires raising the incoming water temperature or adjusting/replacing the thermostat. Other causes include a defective detergent injector (replace squeeze tube or injector motor, clean tubing), wares incorrectly loaded (reposition or reduce wares), or tripped high limits (reset or replace). Also, review the troubleshooting steps for chemical feed and water supply issues, as these can also impact wash quality.
M
Mr. Robert KelleyAug 19, 2025
How to fix a Champion Dishwasher that will not run?
- E
  Emily MannAug 20, 2025
  If your Champion Dishwasher isn't running, make sure the door is completely closed. Also, check the breaker on the panel to ensure the main power is on, and verify that the dishwasher itself is turned on.
A
albertturnerAug 22, 2025
What to do if my Champion Dishwasher has low or no water?
- A
  Anthony RowlandAug 22, 2025
  If you're experiencing low or no water in your Champion Dishwasher, begin by checking if the main water supply valve is open. If it is open, the issue might be a defective solenoid valve (install repair kit or replace), a clogged solenoid strainer (clean strainer), a defective flow washer (replace flow washer), or a defective timer board (test/replace timer board).
T
Timothy RamirezAug 26, 2025
What to do if there is low or no water in my Champion UH-200 Dishwasher?
- J
  Justin SellersAug 26, 2025
  If your Champion Dishwasher has low or no water, the main water supply might be off. Alternatively, the solenoid valve or strainer could be defective or clogged, or the flow washer or timer board might be defective. Try opening the supply valve, cleaning the strainer, or replacing the flow washer. You may also need to install a repair kit or replace the solenoid valve, or test and replace the timer board.
D
Daniel CastroAug 28, 2025
What to do if my Champion Dishwasher has low water pressure from spray arms?
- P
  Paula WilliamsAug 28, 2025
  If you're experiencing low water pressure from the spray arms in your Champion Dishwasher, it could be due to a clogged scrap screen, clogged spray arms, or a clogged pump intake screen. Try cleaning the scrap screen and spray arms. You should also inspect the sump and clean the pump intake screen.
D
Danielle Haney DVMAug 31, 2025
How to increase water pressure in Champion Dishwasher spray arms?
- P
  Peter YoungAug 31, 2025
  If the water pressure from the spray arms of your Champion Dishwasher is low, it may be due to a clogged scrap screen, clogged spray arms, or a clogged pump intake screen. To resolve this, clean the scrap screen and spray arms. Also, inspect the sump and clean the pump intake screen.
A
April JacksonSep 3, 2025
Why aren't chemicals feeding into my Champion UH-200?
- Z
  Zachary MurphySep 3, 2025
  If chemicals aren't feeding into your Champion Dishwasher, the chemical supply may be low (refill the container), the supply tubing may be damaged (replace tubing) or kinked (straighten tubing), the pick-up tube may be clogged (clean or replace), or the timer board may be defective (test or replace).
M
Miss Caitlin DavisSep 6, 2025
What to do if water drains from my Champion UH-200 Dishwasher when idle?
- Z
  zmccormickSep 6, 2025
  If water drains out of the wash tank of your Champion Dishwasher while it's idle, ensure the goose-neck loop in the drain hose hasn't been removed; re-route the drain hose, being careful not to stretch it. Also, check the drain hose clamp to make sure it's holding the hose in the proper position, maintaining the goose-neck. If the issue persists, it may be due to the building's plumbing not providing correct air vent to prevent siphoning, and you should contact a service agent or plumber.
J
Jimmy SchmittSep 9, 2025
Why does my Champion UH-200 Dishwasher (HT model) stay in the wash cycle?
- R
  Rachel SmithSep 9, 2025
  If your HT model Champion Dishwasher stays in the wash cycle, it might be because the Rinse Sentry extends the wash mode for up to 5 minutes to allow the final rinse water booster temperature to reach 180°F/82°C. Also, check if the dishwasher is in Extended Wash Mode (UH200B, UH200, UH170B models only). To address this, raise the incoming water temperature, adjust or replace the final rinse booster thermostat, or turn off Extended Wash Mode.
M
Mr. Barry HernandezSep 12, 2025
Why are the wash results poor in my Champion UH-200 Dishwasher?
- J
  James ColemanSep 12, 2025
  Poor wash results from your Champion Dishwasher can stem from several issues. The water temperature might be too low, or the thermostat could be defective and require adjustment or replacement. A defective detergent injector, incorrectly loaded items, a tripped booster high limit, or a tripped wash tank high limit could also be the cause. Try raising the incoming water temperature, repositioning the wares, reducing the amount of wares, or resetting/replacing the high limit. Also consider replacing the squeeze tube or injector motor, and cleaning the tubing and pick-up.