Champion UL130 M4 - User Manual

Questions and Answers

M
Morgan DavisAug 4, 2025
Why is there low or no water in my Champion Dishwasher?
- M
  Matthew BryantAug 4, 2025
  If your Champion Dishwasher isn't filling with water, here are some possible reasons: * The main water supply is off: Open the supply valve. * The fill hose is kinked: Straighten the fill hose. * The incoming water pressure is low: Set the flowing water pressure to 20-22 PSI. * The solenoid valve is defective: Install a repair kit or replace it. * The solenoid strainer is clogged: Clean the strainer. * The circuit board fuse is blown: Contact your service agent.
M
Mr. Brandon PetersonAug 8, 2025
Why aren't chemicals feeding into my Champion UL130 M4 Dishwasher?
- L
  larryhoustonAug 8, 2025
  If chemicals aren't feeding into your Champion Dishwasher, consider these possibilities: * The chemical supply is low: Refill the chemical container. * The supply tubing is damaged: Replace the tubing. * The supply tubing is kinked: Straighten the tubing. * The pick-up tube is clogged: Clean or replace the tube. * The chemical circuit board fuse is blown: Contact your service agent.
M
Michael GarciaAug 12, 2025
What to do if water has drained out of the wash tank of my Champion UL130 M4 Dishwasher while idle?
- N
  Natasha VangAug 13, 2025
  If water drains from the wash tank of your Champion Dishwasher when it's not in use: * The anti-siphon loop in the drain hose has been removed: Re-route the drain hose. * The drain hose clamp isn't holding the drain hose correctly: Replace or adjust the hose clamp, ensuring the goose-neck is maintained. * The building plumbing lacks a correct air vent: Contact a service agent or plumber.
D
David MasonAug 17, 2025
What to do if my Champion Dishwasher has poor wash results?
- B
  Benjamin SparksAug 17, 2025
  If your Champion Dishwasher isn't cleaning dishes well, several factors could be the cause: * Excessively hard water: Contact your chemical supplier. * Low water temperature: Increase the incoming water temperature to 140°F. * Defective thermistor: Replace the thermistor. * Defective detergent injector: Replace the injector motor. * Chemical circuit board fuse blown: Contact your service agent. * Incorrectly loaded wares: Reposition or reduce the number of items in the dish racks. * Booster high limit tripped: Reset or replace the high limit. * Wash tank high limit tripped: Reset or replace the high limit.
M
Megan ReedAug 21, 2025
What to do if my Champion Dishwasher will not run?
- D
  davidgonzalezAug 21, 2025
  If your Champion Dishwasher isn't starting, make sure the door is completely closed, check the breaker on the panel, and ensure the dishwasher power switch is turned ON.
K
karen12Aug 26, 2025
Why is my Champion Dishwasher staying in the wash cycle?
- E
  Ellen MeltonAug 26, 2025
  Your Champion Dishwasher might remain in the wash cycle due to a few reasons: * The incoming water supply is cold: Raise the incoming water temperature. * The Rinse Sentry is extending the wash mode: Adjust or replace the final rinse booster thermistor. The Rinse Sentry extends the wash mode for a maximum time of 5-minutes to allow final rinse water booster temperature to reach 180°F/82°C. * The dishwasher is operating in Extended Wash Mode (UH230B only): Push the EXT WASH button to exit the Extended Wash mode.
H
hallmaryAug 29, 2025
What causes low water pressure from the wash spray arms in my Champion Dishwasher?
- L
  Leslie MartinAug 29, 2025
  Low water pressure from the wash spray arms in your Champion Dishwasher can be caused by: * A clogged scrap screen: Clean the scrap screen. * Clogged spray arms: Clean the spray arms. * A clogged pump intake screen: Inspect the sump and clean the pump intake screen.