Channel Master 9521A - User Manual

Programmable Antenna Rotator Controller
with Infra-Red Remote Control
Owner’s Guide to Installation and Use
Model 9521A Drive and Controller, 117 VAC
Model 9521EU Drive and Controller, 230 VAC
Model 9537A Controller Only, 117 VAC
Model 9537EU Controller Only, 230 VAC
CAUTION: Read and adhere to all IMPORTANT SAFEGUARDS listed elsewhere in this
booklet. Read and observe safety, installation and operating instructions supplied with
this unit and with your antenna BEFORE installation or operation. Retain this booklet and
all instructions for your safety and future reference.
Controller Compatibility - If purchased separately, the Model 9537 controller may be used with the
following rotator drive units:
Channel Master
®
- Models 9500, 9510(A), 9512, 9513, 9515(A)
Radio Shack
®
- Model 15-1225
If you are upgrading an existing installation with Model 9537 controller, skip to “Model 9537
Programmable Controller” in this leaflet.
Drive Unit Installation
STEP 1 – Determine proper size number of rotator cable from chart. Three conductor cable is
suitable, but if four conductor cable is used, connect both conductors 3 and 4 to terminal 3 of the
terminal board.
Gage No. of Maximum Length
AWG MM Conductors Feet Meters
22 0,6 3 180 55
22 0,6 4* 200 61
20 0,8 3 280 85
20 0,8 4* 310 95
18 1,0 3 445 136
18 1,0 4* 510 155
*Attach 3 and 4 conductors to No. 3 terminals on control and drive.
STEP 2 – Install drive unit. On new drive units, arrow on mast support should be aligned with arrow shaped
mast stop on housing. Install drive unit with arrows pointing south. Using a short piece of mast (3 feet or
less), install the antenna to the drive unit aiming the antenna south. When desired channels are close to or
on opposite sides of the north end stops, the antenna may be installed pointing north. Note, however, that
the antenna will then be pointing in the opposite direction from that indicated on the control.
An alternative means of setting up is to perform a synchronization of the drive unit using the controller.Then
set up the antenna pointing north. Ensure power is disconnected from the controller when
making antenna adjustments.
1

Summary

Owners Guide to Installation and Use

Controller Compatibility

Information on which controllers work with specific rotator drive units.

Drive Unit Installation - Cable Sizing

Determining rotator cable size based on gauge, conductors, and length.

Drive Unit Installation - Mounting and Wiring

Mast Mounting and Orientation

Instructions for mounting the drive unit on a mast and orienting the antenna.

Terminal Connections for Rotator Cable

Guidance on connecting the rotator cable wires to the drive unit terminals.

Model 9537 Features and Components

Controller and Remote Overview

Description of the Model 9537 controller, handheld remote, and power supply.

Controller Installation and Setup

Power and Initial Setup

Determining voltage, connecting power, and checking initial display status.

Connecting Controller to Drive Unit

Wiring instructions for connecting the controller to the drive unit terminals.

Initial Operation and Synchronization

Performing synchronization and understanding the digital compass display.

Operation From The Supplied Handheld Remote

Programming Preset Locations

Step-by-step guide to finding and memorizing antenna locations.

Accessing Preset Locations and Displaying Status

How to recall stored locations and view system status information.

Deleting Programmed Locations;Reset

Procedure for clearing all stored memory locations and resetting the unit.

Advanced Operation and Settings

Synchronization and Timeout Functions

How to re-synchronize the unit and enable automatic timeout features.

Using Universal Remote Controls

Information on configuring and using universal remotes with the controller.

Appendices and Troubleshooting

Common Problems and Solutions

Common issues encountered and their troubleshooting steps.

Handheld Remote Command Summary

A quick reference for handheld remote control commands.

Important Safeguards and Safety Precautions

Limited Warranty Information

Channel Master 9521A Specifications

General

Brand	Channel Master
Model	9521A
Category	Remote Control
Language	English