6-4626
Shut-off Handle
Mango de cierre
Poignée du robinet
6-6136
Hose
Manguera
Tuyau
2. Nozzle/Extension
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6. Pressurizing and Spraying
8. Care, Storage and Maintenance
6-6003
Nozzle
Tobera
Buse
019235R0823
6-3337
Strap,
Correa,
Sangle
Adjust spray pattern
by turning nozzle cap.
Do not turn cap more
than 2 turns or cap may
come off allowing spray
material to spray back
on you.
7. To Release Pressure
1. Hose to Tank
Make sure white outlet tube
is attached to hose.
Insert tube into tank. Proper placement of
white outlet tube.
Line up tabs on safety lock
connector with notches on
the outlet flange of the tank.
Insert tabs into notches to
form a secure seal.
Slip hose nut down to
tank, turn clockwise
and tighten as tight
as possible by hand.
Do: Turn handle clockwise
to tighten. Push handle
down, turn 1/4 turn
counterclockwise to
release.
Do: Pump until you feel
resistance.
Do: Push handle, down,
turn 1/4 turn clockwise to
lock. Begin spraying. Re-
pump sprayer as required
to maintain spray force.
1A
1D
1E
For constant spraying, push down on shut-off handle and move grey locking
mechanism away from you. To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are provided with this feature).
9A
Locking
mechanism
3. Filter
The filter helps prevent clogging while spraying. It is located on the
end of the outlet tube inside your sprayer tank.To clean filter, remove
the discharge assembly from the tank (Fig.1A). Make sure the filter is
positioned at the bottom of the tank as pictured (Fig. 3A).
Filter
3A
6B6A 6C 6D
6-7770
Extension wand, Vara de extensión, Rallonge
6-4631
Fan Nozzle
Tobera
Buse
Attach nozzle to shut-off handle or extension wand.
2A
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
9. Fatigue-Free Spraying
TO EXTEND EXTENSION - Grasp locking nut and turn counter-clockwise
until loose. Pull brass tube up to desired length and re-tighten locking
nut by turning clockwise until tight. DO NOT USE TOOLS AS THIS WILL
DAMAGE EXTENSION.
TO RETRACT EXTENSION - Grasp the locking nut and turn it counter-clockwise until loose. Push the brass tube
down into the base tube to desired length (CAUTION: POINT THE NOZZLE IN A SAFE DIRECTION. IF THE EXTENSION
HAS FLUID IN IT THE FLUID WILL SPRAY OUT OF THE NOZZLE WHEN PUSHING THE BRASS TUBE DOWN, POSSIBLY
CAUSING IT TO SPRAY ON YOU. YOU CAN ELIMINATE THIS BY REMOVING THE EXTENSION FROM THE SHUT-OFF AND
ALLOWING THE FLUID TO DRAIN.) Re-tighten the locking nut by turning it clockwise to hold brass tube in position.
2B
2C
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace
hose before using. Replace with original manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer’s part before using.
10. Troubleshooting
-
Tank pressurizes but does not spray.
WARNING:
Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 10A- 10D)
Pull handle
straight up.
Insert notches
from underside of
handle into plunger
grooves and turn
counterclockwise.
Tighten plunger clockwise until
flush to top of shut-off body. Do
not over-tighten or unit may not
spray. Slide forks under plunger,
push handle down until it snaps
into place.
10A
10B
Handle
10D
Plunger flush
with body
Remove plunger, diaphragm and
spring. Wash diaphragm with
mild detergent. Reassemble: Hold
shut-off upright as shown, place
spring in hole, place diaphragm on
top of spring. Reassemble plunger
and tighten.
10C
Plunger
Spring
Diaphragm
Sk-1154-1
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
BEFORE RETURNING THIS PRODUCT FOR ANY REASON, PLEASE CALL:
1-800-950-4458
When calling, please have the following information available: Sales receipt & model number. This number
connects you directly with the manufacturer of this product. Our Technical Support Team will be happy to help
you with any assembly, troubleshooting and replacement information you may need.
CONGRATULATIONS!
YOU HAVE JUST PURCHASED A QUALITY CHAPIN PRODUCT.
REGISTER YOUR SPRAYER ONLINE @ WWW.CHAPINMFG.COM
VISIT US ON THE INTERNET: WWW.CHAPINMFG.COM
6-1925
Repair Kit (not included)
Juego de reparación (no incluido)
Kit de réparation (non inclus)
Clean Nozzle Assembly (Fig. 10E)
10E
Nozzle Cap
Remove nozzle cap by unscrewing.
Clean and re-assemble.
1B 1C
1) Do: Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with recommended solvent.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the
wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com
WARNING
2553E
To Next Page
Need help?
General
