Chicco 360 - Securing the Chair on the Table

10
11
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean
COMPONENTS
A - Chair seat (gure 1)
B - Rotating part of the chair (gure 1)
C - Fixed part of the chair (gure 1)
D - Rotating handle (gure 1)
E - F - Arms (gure 2)
G - Rear fastening pins (gure 2)
GG - Rear joint buttons (gure 2)
GGG - Rear joint screws (gure 2)
H - Front fastening pins (gure 2)
HH - Front joint buttons (gure 2)
I - Non-slip plastic tips
ASSEMBLY
1. Remove the product from the mesh bag.
2. Connect the two arms (E, F) to the seat structure. Insert
one arm at a time into the tube of the structure as shown
in Figure 3, making sure that the two pins in the tube of
the structure have exited completely through the holes
in the arm (E-F). An audible click indicates that they were
inserted correctly (see gure 4). Warning: to make assem-
bly easier, there is a marking on one of the two arms and
on one of the tubes of the structure to indicate that these
two parts must be assembled together. Repeat the oper-
ation for the other arm.
USE
3. To fasten the chair to the table, turn the joint screws
(GGG) clockwise as indicated by the symbols on the
screws themselves, see gure 5.
4. Press the buttons on the joints (GG - HH), gure 6, until
the pins are completely lowered. Incline the seat, lifting
the rear part, and position it on the table surface (gure
7). Push the seat in fully.
5. Push up the four pins (G-H) until they come into contact
with the bottom surface of the table (gure 8).
6. Make the nal adjustment by turning the screws (GGG)
COUNTERCLOCKWISE until the seat is properly fastened
(gure 9). At this point, check that the non-slip plastic
tips (I) adhere completely with the table surface. If they
do not adhere perfectly, continue turning the fastening
screws (GGG), always counterclockwise, until the non-
slip plastic tips adhere completely with the table surface.
Check the seal by trying to pull the seat outwards. At this
point, the seat is ready to be used.
USING THE SAFETY HARNESS
7. Remember to always fasten the safety harness, making it
pass through the plastic “D” rings (gure 10). After placing
the child in the seat, fasten the plastic buckle as shown
in gure 11. Make sure it is correctly positioned and cor-
rectly fastened.
SEAT ADJUSTMENT
The position of the seat can be selected.
8. To adjust the seat position, lift the handle (D) located on
the backrest of the seat by extracting the pin from the
tube (gure 12), and turning the chair seat in a clock-
wise or counterclockwise direction (gure 13) until the
360° symbol located on the rotating part of the seat (B)
is aligned with the selected symbol located on the xed
part of the chair seat (C). Once the indicated position is
reached, release the rotation handle so that the locking
pin engages in the hole in the tube: an audible click indi-
cates that the pin engaged correctly.
The chair has six positions:
- 1 “FEEDING BOTTLE” position (gure 14 and gure 14a),
2 “BISCUIT” positions (gure 15 and gures 15a/15b): the
360° indicator is positioned in correspondence of the
“FEEDING BOTTLE/BISCUIT” symbol on the tube of the seat
(C). the child is facing outwards and is able to drink from
the feeding bottle or eat a snack independently, always
keeping the visual contact with his mum, who is able to
move freely in the surrounding area.
- 2 “CUP” positions (gure 16 and gures 16a/16b): the 360°
indicator is positioned in correspondence of the “CUP”
symbol on the tube of the seat (C). The moment of wean-
ing is experienced with the correct contact between the
child and his mum. The child is able to pick up the cup lo-
cated on the table on his own while the mother is able to
be in a correct position near her child while feeding him.
- 1 “CUTLERY” (gure 17 and gure 17a): the 360° indicator
is positioned in correspondence of the “CUTLERY” symbol
on the front part of the xed structure (C). Once the child
has acquired greater autonomy, he faces towards the ta-
ble and is able to enjoy being at the table together with
his mum and dad.
WARNING! do not adjust the seat to a position of use other
than those indicated in this instruction booklet. The seat
must never be adjusted while the child is sitting in it. In this
case it can be slightly more dicult.
WARNING! While adjusting the seat, make sure that the
child's legs can freely follow the movement of the seat.
HOW TO REMOVE THE FABRIC COVER
The cover of the hook on chair can be removed for washing.
9. Unfasten the safety harness and remove it from the plas-
tic ”D” rings.
10. Unfasten the 4 snap buttons integrated in the fabric
(gure 18a and 18b).
11. Remove the plastic “D” rings, making them pass through
the openings in the seat fabric.
12. Remove the two rear metal hooks of the seat, making
them pass through the seats in the backrest and the
three metal front hooks through the seats along the
front edge of the seat (gure 19a and 19b). At this point,
the fabric can be removed.
13. Unfasten the snap button located on the seat (gure 20)
and remove the HDPE insert.
To recover the chair, proceed as follows.
14. Insert the HDPE insert on the bottom of the chair and
close the snap button.
15. Insert the metal hooks through the specic seats and
make sure that they are correctly blocked as shown in
gure 21a and 21b.
16. Pass the plastic “D” rings through the openings in the
seat fabric.
17. Clasp the snap buttons in the fabric to the seat structure.
18. Pass the safety harness through the plastic “D” rings. At
this point, the seat is ready to be used.
DISASSEMBLY AND TRANSPORT
Proceed as follows for product disassembly.
19. Press the locking pins located in the arms (G - H) and
pull them out of the seat.
20. Insert the seat (A) and the two disassembled arms in the
provided mesh bag (gure 22). The product is ready to
be transported.
WARRANTY
The product is guaranteed against any conformity defect in
normal conditions of use as provided for by the instructions
for use. The warranty shall not therefore apply in the case
of damages caused by improper use, wear or accidental
events. For the duration of warranty on conformity defects
please refer to the specic provisions of national laws appli-
cable in the country of purchase, where provided.
FOR FURTHER INFORMATION, PLEASE CONTACT:
ARTSANA UK Ltd.
Prospect Close - Lowmoor Road
Industrial Estate - Kirby in Asheld
Nottingham NG 17/7 LF - England
U.K.
Tel. +44 1623 750870 (oce hours)
www.chicco.com