H00701:07/01 DOUBLE D ROPSIDE CRIB
child craft
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: 812-883-1819 - http://www.childcraftindustries.com
ASSEMBLY DIRECTIONS AND PARTS LIST
ΦREAD ALL INSTRUCTIONS WITH CARE BEFORE STARTING THE ASSEMBLY PROCEDURE.
ΦΦ
ΦΦ
ΦYOU WILL NEED A #2 PHILLIPS SCREWDRIVER, A SLOTTED SCREWDRIVER AND A HAMMER.
PARTS INCLUDED IN H ARDWARE B AG ( NOTED WHEN SHOWN ACTUAL SIZE)
(18) Slotted/Phillips
Wood Screws
E
(12) Slotted/Phillips
Machine Screws
A
(actual size)
B
(4) Spring Hangers
C
(4) Gate Shoes
D
(2)
Moulded
plastic
backers
(2)
4-Position
Spring
Hanger
Brackets
(actual size)
F
(4) Compression
Springs
G
(4) Bumper
Springs
H
(4) Casters
(style may vary)
I
(2) Angle
Brackets
PARTS I NCLUDED IN C ARTON
O
(1) Footboard
N
(1) Headboard
P
(2) Dropsides
R
(1) Spring
J
(2) Stabilizer Bars
K
(4) Crib Rods
PREPARATION
Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars
JJ
JJ
J and the (4) Crib Rods
KK
KK
K to Crib Spring
RR
RR
R. Check
quantities and match to the two Parts Included lists above. If any part is missing or broken contact your dealer or Child Craft at ph. (812) 883-3111, or
http://www.childcraftindustries.com for a replacement part or instructional literature. Before making this contact, identify your crib by its model identification
number as stamped or otherwise labeled on the underneath side of the bottom rail of either Headboard
NN
NN
N, Footboard
OO
OO
O, or a Dropside
PP
PP
P.
Record the Model Identification Number now: # ______________________. Include this number with a request for a part or instructional literature.
DO NOT SUBSTITUTE PARTS!
Note the two piece assembly of 4-Position Spring Hanger Brackets
DD
DD
D. Before
attachment to Headboard
NN
NN
N & Footboard
OO
OO
O, check to be sure the moulded plastic
backer aligns with the 4-Position Spring Hanger Bracket
DD
DD
D as shown. These items
are shipped assembled, in the unlikely event they should become detached during
shipment, simply take the plastic backer, align with the holes in the metal bracket
and snap together to create an assembly as shown in the Parts Included list
above. IMPORTANT! All four plastic tabs on each moulded plastic backer should
project toward the metal hooks on 4-Position Spring Hanger Brackets
DD
DD
D. If you
should find a tab on an
uninstalled
4-Position Spring Hanger Bracket
DD
DD
D not so
projected, simply use a screwdriver to push the tab forward until it contacts the
metal hook. If a plastic tab is not projected on a
factory installed
4-Position Spring
Hanger Bracket
DD
DD
D, simply place a small slotted screwdriver underneath the plastic
tab and pull forward until it contacts the metal hook. Attach a 4-Position Spring
Hanger Bracket
DD
DD
D, to both Headboard
NN
NN
N & Footboard
OO
OO
O with Slotted/Phillips
Wood Screws
EE
EE
E. Position exactly as the ones already factory installed. Attach
Angle Brackets
II
II
I with Slotted/Phillips Wood Screws
EE
EE
E to Headboard
NN
NN
N
and
Footboard
OO
OO
O. Position exactly as the ones already factory installed.
DO NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER
HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS
EE
EE
E.
STEP 1 - DIAGRAM 1: ATTACH 4-POSITION S PRING H ANGER B RACKETS AND ANGLE B RACKETS.
E
E
I
D
Factory
installed
O
Holes to
receive
Slotted/
Phillips
Wood
Screws
EE
EE
E
D
1
To Next Page
Need help?
General
