Christie CP2215 User Manual (English)

Other manuals for Christie CP2215

User Manual104 pages

Service Manual86 pages

Quick Start Guide38 pages

Questions and Answers:

H
Hannah RodriguezAug 19, 2025
What to do if my Christie CP2215 Projector does not turn on?
- V
  Vanessa SheltonAug 19, 2025
  First, ensure the power cord is correctly connected to both the projector and the AC power supply, and that the input selector switch is in the right position. Next, check if the wall circuit breaker is on; if it's frequently tripping, consult a certified electrician. Also, verify that the touch panel controller (TPC) is on and its input panel LEDs are lit. If the TPC is off, confirm that the AC outlet the projector is connected to is working and the TPC is properly connected to the projector. If the TPC is connected and the LEDs are lit, check the Operational Status region on the TPC's Main panel to ensure there isn't a PIBS1 failure indicated.
P
parksdeannaAug 26, 2025
What to do if Christie CP2215 Projector won't power on from standby?
- M
  moralesrhondaAug 26, 2025
  If your Christie Projector does not move from standby to full power mode, first check the touch panel controller (TPC) for any error messages. If there is a failure with PIB communications, try reseating the board. Check the Ethernet status LED on the rear of the TPC. Also, verify that the internal fans are operating and that the green LED is lit (indicating the LVPS is operating), visible through the service panel. Check all harness connections between the LVPS and backplane, paying close attention to the small, white connector on the LVPS. If none of these steps work, consider replacing the LVPS.
D
Dennis SteeleAug 28, 2025
What to do if Christie Projector does not move from standby to full power mode?
- A
  Anna DunnAug 28, 2025
  Check the touch panel controller (TPC) for any error messages. If there is a PIB communications failure, try reseating the board. Also, check the Ethernet status LED on the rear of the TPC and verify that the internal fans are running. Look through the service panel to verify the green LED is lit, indicating the LVPS is operating. Inspect all harness connections between the LVPS and backplane, paying close attention to the small, white connector on the LVPS. If the issue persists, consider replacing the LVPS.
M
melissahigginsAug 30, 2025
What to do if my Christie CP2215 won't move from standby to full power mode?
- L
  Lori CaldwellAug 30, 2025
  If your Christie projector is stuck in standby mode, try the following: * Check the touch panel controller (TPC) for any error messages. * If there's a failure with PIB communications, try reseating the board. * Examine the Ethernet status LED on the rear of the TPC. * Make sure the internal fans are running. * Look through the service panel to see if the green LED is lit. * Check all harness connections between the LVPS and the backplane, paying close attention to the small, white connector on the LVPS. * Replace the LVPS.
S
Scott SotoSep 1, 2025
Why does my Christie CP2215 show a DMD over-temperature warning?
- S
  Stephanie MaloneSep 2, 2025
  If you're getting a DMD over-temperature warning on your Christie Projector, first go to Menu > Status and then Temperatures in the left pane to see if the DMD temperatures are too high. If they are, turn the lamp off and let the cooling fans cool the projector. Next, check the air filters and clean or replace them if they're dirty. Finally, make sure all the fans are running properly.
S
Shawn KennedySep 4, 2025
Why is my Christie CP2215 showing a DMD over-temperature warning?
- R
  Ronald BurtonSep 4, 2025
  Navigate to Menu > Status, then Temperatures in the left pane, and check if the DMD temperatures are excessively high. If they are, turn off the lamp and allow the cooling fans to cool the projector. Also, inspect the air filters and clean or replace them if they appear dirty. Finally, ensure that all fans are functioning correctly.
C
cooksamuelSep 6, 2025
How to troubleshoot the touch panel controller of my Christie Projector?
- D
  davistravisSep 6, 2025
  First, ensure the TPC is properly connected to the projector. If the TPC fails to initialize, check that the compact flash on the left side is correctly installed and restart the projector. If button presses on the screen aren't interpreted correctly, recalibrate the TPC screen by tapping Menu > Administrator Setup > Preferences, then tap Calibrate Screen and follow the on-screen instructions.
B
Bobby RuizSep 8, 2025
What to do if I cannot establish communication with my Christie CP2215 Projector?
- G
  gthompsonSep 8, 2025
  Verify that all input devices have the same subnet mask and gateway, and that they all possess unique IP addresses.
E
emilysteeleSep 12, 2025
What to do if my Christie Projector shows a DMD over-temperature warning?
- E
  emartinSep 12, 2025
  If your Christie Projector is displaying a DMD over-temperature warning, take these steps: 1. Go to Menu > Status, then Temperatures in the left pane to see if the DMD temperatures are too high. 2. If they are, turn off the lamp and let the cooling fans cool the projector. 3. Inspect the air filters; clean or replace them if they're dirty. 4. Ensure that all fans are working.
B
Brian PenaSep 13, 2025
How to fix touch panel controller issues with Christie CP2215?
- J
  Jonathan HallSep 13, 2025
  If you're experiencing issues with the touch panel controller on your Christie projector: * First, ensure the TPC is properly connected to the projector. * If the TPC isn't initializing, check that the compact flash on the left side is correctly installed. If it still fails, try restarting the projector. * If button presses on the screen aren't registering correctly, the TPC screen might need recalibrating. You can do this by tapping Menu > Administrator Setup > Preferences, then Calibrate Screen, and following the on-screen instructions.

Christie CP2215 Specifications

General

Contrast Ratio	2000:1
Technology	DLP
Type	Digital Projector
Resolution	1920 x 1080
Brightness	15000 ANSI Lumens
Lamp	Xenon lamp
Input Connectors	HDMI, DVI, VGA
Lamp Life	1000 hours (Xenon lamp)