Chrysler Imperial 1957 User Manual

Procedure for contacting the factory for assistance or advice on service matters.

Details on ordering parts, including addresses and procedures for different areas.

Information on vehicle and engine numbering methods for 1957 models.

Provides key specifications and starting vehicle numbers for 1957 models.

Technical data and specifications for manual and power steering systems.

List of specialized tools required for front wheel suspension servicing.

Specifications for rear axle types, gear ratios, bearings, and clearances.

List of special tools required for rear axle service procedures.

Specifications for center plane service brakes, including lining and cylinder details.

List of specialized tools for brake system servicing.

Specifications for clutch components, including facings, springs, and pedal free play.

List of specialized tools for clutch service operations.

Specifications for cooling system components like fan, radiator, and thermostat.

List of special tools for servicing the cooling system.

Specifications for battery, starter, electrical light bulbs, generator, and regulator.

Detailed specifications for engine types, crankshaft, connecting rods, and pistons.

Procedures for performing minor engine repairs and tune-ups.

Procedures for major engine tune-ups, including compression tests.

Step-by-step instructions for removing the engine assembly from the car.

Instructions for installing the engine assembly back into the car.

Procedure for removing cylinder heads, including related components.

Instructions for installing cylinder heads and related parts.

Procedure for installing the rocker arm and shaft assembly.

Instructions for removing valves and valve springs from the cylinder head.

Steps for inspecting valves, including wear and damage checks.

Procedure for removing and installing valve guides.

Instructions for refacing valves and valve seats.

Method for testing valve springs using a spring tester.

Information on hydraulic tappets, including noise diagnosis and removal.

Procedure for checking engine valve timing using a dial indicator.

Procedure to locate the low point of the camshaft relative to tappet face.

Instructions for removing the timing gears and chain assembly.

Procedure for installing the timing gears and chain assembly.

Steps for removing the camshaft.

Procedure for removing and installing the distributor drive shaft bushing.

Instructions for installing the camshaft.

Procedure for cleaning and inspecting the cylinder block.

Instructions for fitting pistons into the cylinder bores.

Procedure for measuring and fitting piston rings into cylinder bores.

Information on connecting rods, including identification and assembly.

Method for checking connecting rod bearing clearance using Plastigage.

Procedure for installing piston and connecting rod assemblies into the cylinder block.

Inspection of crankshaft journals for wear, taper, and scoring.

Information on crankshaft bearings, including interchangeability and sizes.

Procedure for removing and installing main bearings.

Method for checking main bearing clearance.

Procedure for installing main bearings.

Description of the fuel pump's operation and components.

Procedures for servicing the fuel pump, including disassembly and cleaning.

Troubleshooting guide for fuel pump issues.

Step-by-step instructions for disassembling the BBD-2527S carburetor.

Procedure for assembling the carburetor.

Instructions for adjusting the carburetor settings.

Instructions for disassembling WCFB carburetors.

Procedure for assembling the WCFB carburetor.

Instructions for adjusting the WCFB carburetor.

Troubleshooting guide for carburetor issues.

Procedures for servicing intake and exhaust manifolds.

Description and operation of the manifold heat control valve.

Troubleshooting guide for exhaust system components.

Specifications for frame and rear springs.

List of essential tools for servicing frames, springs, and shock absorbers.

Procedures for manual steering gear removal, assembly, and adjustment.

Procedures for coaxial power steering unit removal, assembly, and testing.

Specifications for manual and power steering systems.

List of special tools for manual and coaxial power steering.

Procedures for removal, assembly, and adjustment of the standard 3-speed transmission.

Information on TorqueFlite transmission operation, components, and servicing.

Explanation of the construction and operation of the planetary gear set.

Description of the two types of universal joints used on 1957 Chrysler Models.

Procedure for servicing cross type universal joints.

Procedure for servicing ball and trunnion type universal joints.

Maintenance guidelines for universal joints.

Information on the rear axle control strut and its purpose.

Procedure for checking propeller shaft angles.

Procedures for checking wheels for eccentricity and tightening hub nuts.

Information on tubeless tires, dismounting, mounting, and repair.

Troubleshooting guide for wheel and tire issues like leakage and thump.

Information on body maintenance, features, and bolt tightening specifications.

Procedures for testing the car for water or dust leaks.

Details on MOPAR Super Rubber Cement and other sealing compounds.

Recommendations for engine oil, lubricants, and service intervals.

Information on radio removal, installation, and operating controls.

Instructions for operation and care of the Hi-Fi record player.

Data and specifications for the Airtemp compressor.

Explanation of the heater-air conditioner controls and their operation.

Information on how cooled or heated air is distributed.

Details on temperature control settings for cooling and heating.