EasyManua.ls Logo

Cisco 1600 - Page 24

Cisco 1600
63 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Loading...
about management interfaces, see the Cisco Secure Firewall Management Center Administration Guide and
about network topology, see the Cisco Secure Firewall Management Center Device Configuration Guide.
Each management center-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial
EEPROM that is encoded with security information. This encoding allows us to identify and validate that the
SFP transceiver meets the requirements for the chassis.
Only management center-supported SFP+ transceivers are compatible with the 10-Gb interfaces.
Cisco TAC may refuse support for any interoperability problems that result from using an untested
third-party SFP transceiver.
Note
Step 4 (Optional) eth3 management interface —Install any management center-supported SFP+ transceiver and cable
in this 10-Gigabit Ethernet SFP+ interface as needed. You can connect this interfaces to the same or different
network from your other management interfaces depending on your network needs. For more information
about management interfaces, see the Cisco Secure Firewall Management Center Administration Guide and
about network topology, see the Cisco Secure Firewall Management Center Device Configuration Guide.
Each management center-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial
EEPROM that is encoded with security information. This encoding allows us to identify and validate that the
SFP transceiver meets the requirements for the chassis.
Only management center-supported SFP+ transceivers are compatible with the 10-Gb interfaces.
Cisco TAC may refuse support for any interoperability problems that result from using an untested
third-party SFP transceiver.
Note
Step 5 (Optional) USB port —Connect a keyboard to the USB port.
You can use this connection and a monitor that is connected to the VGA port to configure network settings
for the management center before performing initial setup using the web interface; see (Optional) Configure
Network Settings Using a Physical Connection for Software Versions 6.3 - 6.4, on page 25.
Step 6 (Optional) VGA port —Connect a monitor to the VGA port.
The management center sends console messages to the VGA port by default. You can use this connection and
a keyboard connected to a USB port to configure network settings for the management center before performing
initial setup using the web interface; see (Optional) Configure Network Settings Using a Physical Connection
for Software Versions 6.3 - 6.4, on page 25.
Step 7 (Optional) Use the RJ-45 to DB-9 console cable supplied with the appliance (Cisco part number 72-3383-XX)
to connect a local computer to the management center serial port. (You may need a DB-9-to-USB adaptor to
connect to the local computer.) You can use this connection for serial access (see Set Up Serial Access, on
page 40) and to configure network settings for the management center before performing initial setup using
the web interface; see (Optional) Configure Network Settings Using a Physical Connection for Software
Versions 6.3 - 6.4, on page 25.
Step 8 (Optional) Use an ethernet cable to connect the CIMC port to a local network reachable from a computer
where you run an IPMI utility for Lights-Out Management. See Set Up Lights-Out Management, on page 41
for more information.
Step 9 Power supply—Use one of the supported power cords to connect the power supplies of the chassis to your
power source. For more information about supported power cords, see the Cisco Firepower Management
Center 1600, 2600, and 4600 Hardware Installation Guide.
We recommend connecting both power supplies on the management center to provide redundancy
protection. The appliance generates a health alert if only one power supply is connected.
Note
Step 10 Power—Press the Power button on the front of the chassis, and verify that the power status LED is on.
Cisco Firepower Management Center 1600, 2600, and 4600 Getting Started Guide
24
Firepower Management Center 1600, 2600, and 4600 Getting Started Guide
Connect Cables Turn On Power Verify Status for Versions 6.3 - 6.4

Other manuals for Cisco 1600

Related product manuals