C300 Abbreviated instruction
• To see details of specifications and operations, refer to the instruction manual: C300 instruction manual
English
Component identification
PM
MHP
1:10
1:20
1:30
1:40
1:50
2:00
2:30
3
:30
4:00
4:30
5:00
6:00
7:00
8:00
9:00
3:00
24
2
4
6
8
10
12
14
16
18
22
UTC
24
4
8
12
16
20
PM AM
H.R.
MODE
TME
CAL
AL-1
SET
AL-2
AL-3
CHR
TMR
DOWN
UP
20
UTC hour hand
Hour hand
24-hour hand
UTC minute hand
Button
A
Button
M
Minute hand
Digital display
Mode hand
Button
B
Button
C
• Actual appearance may differ from the illustration.
• Refer also to our web page for detail of usage of the scale and bezel on the watch.
(
http://www.citizenwatch-global.com/support/pdf/enhanced/e.pdf
)
Setting the time
• The time indicated with the hour, 24- hour and minute hands and UTC hour/
minute hands is synchronized with that on the digital display.
• Press and hold button
B
for 2 seconds or more to move the hour and minute
hands to 12 o'clock position temporarily to see the digital display without their
interruption. Press the button again to return them to normal movement.
1.
Press and release the lower right button
M
repeatedly to
move the mode hand to point to [TME].
2.
Press and release the upper right button
A
or lower left
button
C
repeatedly to indicate an area name you want on
the digital display.
3.
Pull out the lower right button
M
.
The time indication on the digital display starts blinking and the time
becomes adjustable.
4.
Press and release the upper right button
A
repeatedly to
change the target to be set.
• Each time you press the button, the target changes as follows:
Summer time Second Minute Hour 12/24-hour
basis
PM
PM
PM
PM
5.
Press and release the lower left button
C
to adjust the target.
• Press button
C
in accordance with a reliable time source to adjust the
second.
• Pressing and holding the button changes indication continuously.
• “AM” or “PM” is displayed to indicate AM or PM in 12-hour basis
indication.
• “SUMMER” is displayed when summer time is activate.
• Summer time cannot be activated when “UTC” is chosen for the area.
6.
Repeat steps 4 and 5 to set other targets.
7.
Push in the lower right button
M
to finish the procedure.
Setting the calendar
The calendar of this watch does not have to be adjusted manually until Thursday,
December 31, 2099 including leap years. (perpetual calendar)
• Press and hold button
B
for 2 seconds or more to move the hour and minute
hands to 12 o'clock position temporarily to see the digital display without their
interruption. Press the button again to return them to normal movement.
1.
Press and release the lower right button
M
repeatedly to
move the mode hand to point to [CAL].
The calendar is indicated on the digital display.
2.
Press and release the upper right button
A
or lower left
button
C
repeatedly to indicate an area name you want on
the digital display.
3.
Pull out the lower right button
M
.
The calendar indication on the digital display starts blinking and the
calendar becomes adjustable.
4.
Press and release the upper right button
A
repeatedly to
change the target to be set.
• Each time you press the button, the target changes as follows:
Month YearDate
5.
Press and release the lower left button
C
to adjust the target.
• Pressing and holding the button changes indication continuously.
6.
Repeat steps 4 and 5 to set other targets.
7.
Push in the lower right button
M
to finish the procedure.
• The day of week is set automatically.
Switching the time of analog and digital sections
The time of the analog section cannot be adjusted directly.
Set the time of the area you want to indicate in the analog section once in the
digital section and then switch the time between the analog and digital sections.
1.
Press and release the lower right button
M
repeatedly to
move the mode hand to point to [TME] or [CAL].
2.
Press and release the upper right button
A
and lower left
button
C
at the same time.
The time of the digital and analog (hour/minute/24-hour hands) sections
switches.
To Next Page
Need help?
General
