Claas LEXION 430 - Page 10

2.1.2 BA LEXION 460 - 410 - 298 425.0
Contents
Steering ........................................................................... 6.4.4
Brakes .............................................................................. 6.4.5
Foot brake ........................................................................ 6.4.5
Parking brake ................................................................... 6.4.6
Stopping the engine ......................................................... 6.4.6
CLAAS Autopilot
(Maize picker head) ......................................................... 6.4.7
CLAAS Autopilot
(Grain cutterbar) .............................................................. 6.4.8
Adjusting the directional stability of the combine ............. 6.4.8
Setting the laser sensor in the field ................................ 6.4.10
Putting the CLAAS Autopilot into operation ................... 6.4.12
Use in rape with left-hand side cutter ............................ 6.4.13
Cutterbar hydraulic cylinders ................................................. 6.5.1
Attaching cutterbar hydraulic cylinders ............................ 6.5.1
Third cutterbar cylinder .................................................... 6.5.1
Rear wheel drive axle ............................................................ 6.6.1
Adjusting rear wheel drive axle from
transport to working position ............................................ 6.6.1
Wheel tread adjustment – Rear wheel drive axle ............ 6.6.4
Adjustable rear axle ......................................................... 6.6.6
Rear axle wheels – steering angle limiter
(Adjustable rear axle) ....................................................... 6.6.8
Side panels ............................................................................ 6.7.1
Opening and closing the side panels and the rear door .. 6.7.1
Adjusting the side panel / rear door locks ........................ 6.7.2
Cabin and lighting .................................................................. 6.8.1
Headlights, worklights and mirrors ................................... 6.8.1
Towing / Crop inspection / Grain tank .................................... 6.9.1
Towing ............................................................................. 6.9.1
Forwards .......................................................................... 6.9.1
Backwards ....................................................................... 6.9.1
Crop inspection ................................................................ 6.9.1
Grain tank ........................................................................ 6.9.2
Closing the grain tank openings ...................................... 6.9.2
Installing dual wheels ........................................................... 6.10.1
Operating the front ladder with dual tyres installed ........ 6.10.5
Additional weights ............................................................... 6.11.1
Liquid filling for rear axle tyres ....................................... 6.11.5
Installing the rear axle weights ...................................... 6.11.5
7. Installing and removing the cutterbar
Installing the cutterbar ............................................................ 7.1.1
Tilting the cutterbar from transport position ..................... 7.1.1
Machines equipped with CLAAS Auto Contour ............... 7.1.2
Adjusting the hydraulic cylinder for
transverse cutterbar control ............................................. 7.1.2
Machines without CLAAS Auto Contour .......................... 7.1.3
Locking cutterbars and maize pickers
(Cutterbars without Auto Contour) ................................... 7.1.5
Connecting the universal drive shafts .............................. 7.1.6
Fitting the stand ............................................................... 7.1.6
Removing the cutterbar .......................................................... 7.2.1
Removing the cutterbar ................................................... 7.2.1
Laying down the cutterbar on the ground ........................ 7.2.1
Placing the cutterbar on the cutterbar trailer .................... 7.2.2
8. Operation CEBIS
9. Operation – basic machine
Feeder housing ...................................................................... 9.1.1
Chains ............................................................................. 9.1.1
Cutterbar reverse drive .................................................... 9.1.2
Cutterbar floatation springs ............................................. 9.1.2
Checking the setting of the cutterbar floatation springs .. 9.1.2
Cutting height indicator .................................................... 9.1.3
Cutterbar spring pressure indicator ................................. 9.1.3
Blocking the cutterbar floatation springs ......................... 9.1.4
Adjusting drop rate of the front attachment ..................... 9.1.4
Cutterbar clutch ............................................................... 9.1.5
Engaging and disengaging the cutterbar ......................... 9.1.5
Threshing mechanism ........................................................... 9.2.1
Stone trap ........................................................................ 9.2.1
Engaging and disengaging the threshing mechanism ..... 9.2.2
Threshing drum ............................................................... 9.2.3
Cleaning the threshing parts ........................................... 9.2.3
Basic concave setting ...................................................... 9.2.4
Learning the limit stops ................................................... 9.2.9
Threshing drum speed .................................................. 9.2.10
Threshing drum drives ................................................... 9.2.10
Threshing drum two-step variable speed drive ............. 9.2.10
Installing and removing preconcave segments ............. 9.2.11
Concave segment ......................................................... 9.2.12
Removing the concave segment ................................... 9.2.12
Installing the concave segment ..................................... 9.2.13
Disawning ...................................................................... 9.2.14
Unslugging the threshing drum ..................................... 9.2.14
Deflector curtain ............................................................ 9.2.15
Straw walkers ........................................................................ 9.3.1
Straw walkers .................................................................. 9.3.1
Intensive separation system ............................................ 9.3.1
Multiple finger separation system .................................... 9.3.2
Cleaning the straw walkers ............................................. 9.3.3
Warning signal ................................................................. 9.3.3
Straw walker risers .......................................................... 9.3.4
Rice risers ....................................................................... 9.3.4
Centre risers .................................................................... 9.3.5
Side risers ....................................................................... 9.3.6
Parallel risers ................................................................... 9.3.7
CCM risers ...................................................................... 9.3.8
Cleaning ................................................................................ 9.4.1
Sieve pan ........................................................................ 9.4.1
Preparation floor .............................................................. 9.4.1
Frogmouth sieves ............................................................ 9.4.2
Electrical sieve adjustment .............................................. 9.4.2
Removing the sieves ....................................................... 9.4.3
Installing the sieves ......................................................... 9.4.6
Tightening torques of axial mountings
for the upper and lower sieves ........................................ 9.4.6
Sieves – Basic setting ..................................................... 9.4.7
Harvesting without finishing sieves ................................. 9.4.7
Cleaning fan .................................................................... 9.4.8
Electric fan speed adjustment ......................................... 9.4.9
Wind-controlled cleaning step
LEXION 460 – 420 .......................................................... 9.4.9
Find manuals at http://best-manuals.com/search?&s=CLA-2984250