Clarion DRX5375R - Basic Operations; Adjusting the Tone; Selecting a Mode; Adjusting the Volume

6. OPERATION
Basic Operations
Be
sure
to
set
the
volume
to
the
minimum
level
before
turning
off
the
power
to
the
unit.
Loud
sounds
when
turning
on
the
power
may
impair
your
hearings
or
cause
damage
to
the
unit.
Turning on the power
Note:
*
Be
sure
to
start
the
engine
before
using
the
unit
to
prevent the battery from running down.
1. Press POWER button [A].
2.
The
illumination
and
display
on
the
unit
light
up.
The
unit
starts
in
the
function
mode
it
was
in
when
the
power
was
turned
off
last.
3.
Press
and
hold
POWER
button
[4]
for
1
sec-
ond
or
longer
to
turn
off
the
power.
Selecting a mode
1.
Press
FUNC
button
[1]
to
select
a
function
mode.
2. The function mode changes in the following
order:
Radio - CD CD changer + Radio ...
* If the CD changer is not connected, the CD
changer mode cannot be selected.
Adjusting the volume
Select
up
or
down
to
increase
or
decrease
using
a-selector [2].
*
Selecting
up
or
down
and
holding
for
1
second
or
longer
on
a-selector
[2]
continuously
increases
or
decreases
the
volume
respectively.
*
The
volume
level
(step
0
to
33)
appears
in
the
dis-
play.
8 DRXAA7AR
Note:
Be
sure
to
read
this
chapter
referring
to
the
front
diagrams
of
chapter
“3.
CONTROLS”
on
page
5
(unfold).
Adjusting
audio
mode
(use
cz
-selector)
Press
A-M
button
[18]
to
select
an
item
to
be
ad-
justed.
Each
time
you
press
the
button,
the
item
changes
in
the
following
order:
Bass/Treble
>
Balance/Fader
-
Mode
display
...
*
The
display
returns
to
the
previous
mode
7
sec-
onds
after
the
adjustment.
Adjusting the tone
Select “BA:TR” (bass/treble) in the display.
@
BASS
adjustment
(step
-6
to
+6)
Select
right
or
left
to
increase
or
decrease.
@
TREBLE
adjustment
(step
—6
to
+6)
Select
up
or
down
to
increase
or
decrease.
a
Tl
rt
!
-T
a a
3]
OT
Get
Fe
RP
Note:
*
When
the
DSP
(Digital
Sound
Processor)
sold
separately
is
connected
to
the
unit,
the
tone
ad-
justment
is
performed
with
the
DSP.
The
DSP
mode
should
be
set
when
it
is
connected.
For
the
setting,
see
the
subsection
“Setting
the
DSP
mode”.
°
When
the
EQ
(Equalizer)
sold
separately
is
con-
nected
to
the
unit,
the
tone
adjustment
is
per-
formed
with
the
EQ.
The
EQ
mode
should
be
set
when
it
is
connected.
For
the
setting,
see
the
sub-
section
“Setting
the
equalizer
mode’.
Adjusting
the
balance
(step
L9
to
R9)
1.
Select
“B:F”
(balance/fader)
adjustment
in
the
display.
2. Select right or left to balance the right or left
sound level.
Adjusting
the
fader
(step
F9
to
R9)
1.
Select
“B:F”
(balance/fader)
adjustment.
2. Select up or down to balance the sound to-
ward the front or rear of the vehicle.