Clarion DRX6575RZ - Basic Unit Operations; Power Management; Mode Selection and Volume Control; Display Switching

1 1 P | 0
| A PFNEDE [AT
mm (1) = ER.
| Vs WI |: RAT
Basic Operations
A ;
Fr tre
à oh LL
F
k
JIN
Le
À
CAUTION
7
Be
sure
to
lower
the
volume
before
switching
off
the
unit
power
or
the
ignition
key.
The
unit
remembers
its
last
volume
setting.
lf
you
switch
the
power
off
with
the
volume
up,
when
you
switch
the
power
back
on,
the
sudden
loud
volume
may
hurt
your
hearing
and
dam-
age
the
unit.
Turning on/off the power
Note:
°
Be
careful
about
using
this
unit
for
a
long
time
with-
out
running
the
engine.
If
you
drain
the
cars
bat-
tery
too
far,
you
may
not
be
able
to
start
the
en-
gine
and
this
can
reduce
the
service
life
of
the
battery.
1. Press POWER button [3].
2.
Theillumination
and
display
on
the
unit
light
up.
The
unit
automatically
remembers
its
last
operation
mode
and
will
automatically
switch
to
display
that
mode.
3.
Press
and
hold
POWER
button
[3]
for
1 sec-
ond
or
longer
to
turn
off
the
power
for
the
unit.
Note:
e System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM CHCK" appears in the dis-
play,
so
press
POWER
button
[3].
The
system
check starts within the unit. When the system check
is complete, the power is turned off, so press
POWER button [3] again.
Selecting a mode
1.
Press
FNC
button
[3]
to
change
the
mode
of
operation.
2.
Each
time
you
press
FNC
button
[3],
the
mode
of
operation
changes
in
the
following
order:
Radio
mode
=
DAB
mode
=>
CD
mode
=
CD
changer
mode
=
MD
changer
mode
=
TV
mode
=
Radio
mode...
+ External equipment not connected with CeNET
is not displayed.
10 DRX6575Rz
Note:
Be
sure
to
read
this
chapter
referring
to
the
front
diagrams
of
chapter
“2.
CONTROLS"
on
page
5
(unfold).
Adjusting the volume
Turning the Rotary knob [15] clockwise increases
the
volume:
turning
it
counterclockwise
decreases
the volume.
*
The
volume
level
is
from
0
(minimum)
to
33
(maxi-
mum).
Switching the display
Press
DISP
button
[10]
to
select
the
desired
display.
Each
time
you
press
DISP
button
fo],
the
display
switches
in
the
following
order:
Main display
= (10) TAGS CSD M23ES 1 (E 1 1
SET
"SE
L
Sub (title) display
(ED TRS CSD) M23ES1 1 (EI 1
«4
KR VAI ML > _.
L- {
D M D MW I
Clock (CT) display
= (10. TRS CS) M23ES | (Ei 1 11
LUINUE
LUE cm
j 1 el _L
wo D.
Ÿ
Main display...
+ Once selected, the preferred display becomes
the display default. When a function adjustment
such as volume is made, the screen will
momentarily switch to that function's display,
then revert back to the preferred display sev-
eral seconds after the adjusiment.
:
When
you
have
entered
a
title
in
a
CD,
it
ap-
pears
in
the
sub
display.
If
you
have
not
en-
tered
a
title,
“NO-TITLE”
appears
in
the
title
display
instead.
For
information
on
how
to
en-
ter
a
title,
refer
to
the
subsection
“Entering
titles”
in
section
“Other
Handy
Functions”.
:
When
CT
data
is
not
received,
“CT--:-—"
appears
in
the
display.