Clarion DXZ938R - REMOTE CONTROL

052-7061-01 M30624MGA-E85GP
LCD & Ce-NET controlter
4.Terminal Description
pin 1
pin 2
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pin
pia
pin 19
pin 20
pin 2)
pin 22
pin 23
pin 24
pin 25
pin 26
pin 27
pin 28
pin 29
NGORONAOCYPONDU SW
oo
pin 30
pin 31
pin 32
pin 33
pin 34
pin 35
pin 36
pin 37
pin 38
pin 39
pin 40
pin 41
pin 42
pin 43
pin 44
pin 45
pin 46
pin 47
pin 48
pin 49
pin 50
pin 51
pin 52
pin 53
pin 54
pin 55
pin 56
pin 57 :
pin 58
“BYTE
VSS
>NMI
LKEY CLK
» KEY D!
:KEY DO
:LCOD SO
:LCD SI
»LCD CLK
-LCD KEY REQ :
:LCD CS
»DISP 5V REM
CONT CONT
NU
NU
NU
REMOCON
CN VSS
INIT 1
INIT 2
RESET
xX OUT
XIN
vec
SYS ACC
BU DET
NG
2? pin connect
NU
NU
NU
NU
KEY STANDBY
ON Board WA
NU
IE BUS ix
IE BUS TX
KEY CHIP s
2NU
>NU
2NU
2NU
2NU
>NU
>NU
2NU
2NU
>NU
oNU
2NU
» MUSIC IND
>» MATRIX IND
» MOVIE IND
‘VIRTUAL IND
: DISC IND
> SCN IND
RPT IND
> RDM IND
DXZ938R
G2 22222:
2:
=O
oO
IN
LCD contrast control voltage output
: Not in use.
otin use.
: Not in use
: Remote controller signal input terminal
‘Input "L" at single mode operation.
‘Input "L" at single mode operation.
Destination setting input. Reter Table 1
Destination setting input. Refer Table 1
: Reset signal input
: Crystal connection
: Negative supply voltage.
Crystal connection.
: Positive supply voitage.
Connect to VCC.
ACC detect signal input.
Backup detection signal input.
Notin use.
: Connect to 27pin.
> Not in use.
Not in use.
: Not in use.
:Notin use
: Standby pulse output for the key scan IC
Input "L" at write mode.
- : Not in use
TIN:
Ox
=Q@
LIN:
70
IN
[0
©)
ae)
70
-IE Bus serial data input.
TE Bus serial data output.
. The chip setect signal output to the key
scan IC.
‘The clock pulse output for the key scan
IC.
Key scan data input.
The serial data output to the Key scan IC
: The serial data output to the LCD driver
The serial data input from the LCD driver
: The clock pulse output to the LCD driver
: The key request signal input from the key
scan IC.
: The chip select signat output to the LCD
driver.
: The power supply circuit contro! signal o-
utput for OCP.
: Not in use.
: Notin use.
: Not in use.
: Not in use.
: Not in use.
: Not in use.
: Not in use.
: Not in use
: Not in use.
: Not in use.
: Not in use.
: Not in use.
: ON command output to the indicator for "M-
USIC".
> ON command output to the indicator for "M-
ATRIX".
> ON command output to the indicator for "M-
OVIE".
: ON command output to the indicator for "V-
iRTUAL".
: ON command output to the indicator for “D-
ISC".
> ON command output to the indicator for "S-
CN".
: ON command output to the indicator for "R-
PT".
> ON command output to the indicator for “R-
DM",
pin 86
pin 87
pin 83
pin 89
pin 99
pin 91:
pin 92
pin 93
pin 94
pin 95 :
pin 96
pin 97
pin 98 :
pin 99 :
pintoo:
Nu
>NU
5 NU
Niu
NU
>NU
OCP DET IN
NU
NU
:NU
AVSS
NU
Vret
AVCC
NU
NU
NU
: Not in use
: Posilive supply voltage
Not in use
- Negative supply voltage
> Not in use
> Not in use.
:Notin use
:Not in use
‘Not in use
:Notin use
Not in use
:
Not
in
use
:
:
Not
in
use
:
Not
in
use
:
Not
in
use
:
Not
in
use
Not in use
Not in use
Jog key signal mput
Jog key signal input
:Notin use
: Not in use
: Not in use.
: Not in use
‘Not in use
Not in use.
Not in use
> Notin use
Not in use
Not in use.
: Not in use
IN:
: Not in use
The DCP detection signal input
- : Notin use.
> Not in use.
: Analog ground.
: Not in use
: Reference voltage.
- : Positive supply voltage for the internal
analog section.
- : Not in use.
: Not in use
: Not in use.
Table 1. The destination setting terminal
North Third
America
area
___dapan
Europa
INITIAL
1
{pin
8)
H
ms
ae.
c
INITIAL
2
(pin
9)
L
L
ae
: