Why won't my Clarion Car Receiver turn on?
If your Clarion Car Receiver isn't powering on, and there's no sound, it could be due to a blown fuse. Replace it with a fuse of the same amperage. If it blows again, it may be due to incorrect wiring, and you should consult your store of purchase.
What to do if there is no sound from Clarion Car Receiver?
If you can't hear any sound from your Clarion Car Receiver, the speaker protection circuit might be activated. Try turning down the sound volume, or turn the power off and on again. If the sound mutes again, it may require service.
How to fix sound skipping on Clarion Car Receiver?
If the sound from your Clarion Car Receiver skips or is noisy, the disc may be dirty. Try cleaning it with a soft cloth. Alternatively, the disc may be heavily scratched or warped, in which case, replace it with a disc that has no scratches.
What to do if Clarion Car Receiver buttons don't work?
If nothing happens when you press the buttons on your Clarion Car Receiver, and the display isn't accurate, the microprocessor may have malfunctioned. Turn off the power, then press the [OPEN] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod. It could also be that the DCP or main unit connectors are dirty, so wipe the dirt off with a soft cloth moistened with cleaning alcohol.
Why is there no sound with amplifiers on Clarion Car Receiver?
If there's no sound output from your Clarion Car Receiver when using amplifiers or a power antenna, the power antenna lead might be shorted or requiring excessive current. Here's what to do: 1. Turn the unit off. 2. Remove all wires from the power antenna lead and check for shorts using an ohm meter. 3. Turn the unit back on. 4. Reconnect each amplifier remote wire one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage.
Why is there no sound from my Clarion Car Receiver disc?
If you're not hearing sound from your Clarion Car Receiver when playing a disc, ensure that the disc contains MP3/WMA files written properly. Also, confirm that the files are recognized as MP3/WMA files and encoded correctly. Finally, verify that the file system used is ISO9660 level 1, 2 or JOLIET or Romeo.
How to stop Clarion Car Receiver sound from cutting out?
If the sound from your Clarion Car Receiver is cutting, skipping, or has noise, the MP3/WMA files may not be encoded properly. Ensure you are using MP3/WMA files encoded correctly.
Why is Clarion Car Receiver sound bad after turning on?
If the sound quality of your Clarion Car Receiver is poor immediately after turning it on, water droplets might have formed on the internal lens due to humidity. Let it dry for about 1 hour with the power on.
What file system for Clarion Car Receiver?
If your Clarion Car Receiver displays the wrong filename, the file system may not be correct. Use ISO9660 level 1, 2 or JOLIET or Romeo file system.
General| Tuner | AM/FM |
|---|---|
| CD Player | Yes |
| MP3 Playback | Yes |
| WMA Playback | Yes |
| AAC Playback | No |
| USB Port/Input | No |
| Bluetooth | No |
| Preamp Voltage | 2V |
| Display Type | LCD |
| DIN Size | Single DIN |
| Detachable Face/Faceplate | Yes |
| Number of Channels | 4 |
| Channels | 4 |
| RMS Power Output | 22W x 4 |
| Auxiliary Input | Yes |
| Equalizer/EQ Settings | 3-band |
| Peak Output | 50W x 4 |
Diagrams and labels for controls on the main unit and access to the detachable panel.
Details the functions of buttons on the main unit of the receiver.
Explains button operations for external equipment and Satellite Radio Receiver.
Step-by-step instructions for removing and attaching the detachable control panel.
Instructions for inserting the battery and details of remote control button functions.
Turning unit on/off, volume, audio modes, display settings, and sound adjustments.
Tuning, seeking, manual tuning, and preset station management.
Playing CDs, MP3s, and WMAs, including file system and playback modes.
Common settings like clock, screen saver, and display adjustments across all modes.
Controlling CD changer functions and TV tuner operations.
Solutions for general issues, power, sound, and CD/MP3/WMA playback errors.
Error codes for CD/MP3/WMA, CD Changer, and DVD Changer operations.
Details on tuner, audio output, player performance, and system specifications.
Steps for mounting the unit using universal and fixed mount options.
General safety advice applicable to both unit operation and installation.
Diagram illustrating the connections for speakers, power, and accessories.
To Next Page
