Why is there a loss of water pressure in my Clearion Water Filtration System?
A loss of water pressure in your Clearion Water Filtration System can occur due to: * Scaling or fouling of the inlet pipe: Clean or replace the pipeline and consider pretreatment to prevent future issues. * Fouled media: Clean the media and pretreat to prevent recurrence. * Improper backwash setting: Increase the frequency of backwashing.
What to do if my Clearion Water Filtration System continuously flows to the drain?
If your Clearion Water Filtration System experiences continuous flow to the drain, it could be due to: * Foreign material in the control valve. * An internal control leak. * The valve being jammed in the backwash, brine, or rapid rinse position. * A stopped or jammed motor. In all of these cases, you should contact your dealer to clean the valve and replace the piston and seals. If the motor is unresponsive, it should also be replaced. Check for jammed piston.
Why does my Clearion Water Filtration System filter fail to regenerate automatically?
The Clearion Water Filtration System filter might fail to regenerate automatically due to: * The power supply being connected to an intermittent or dead power source: Connect to a constant power source. * Improper control valve programming: Reset the program settings. * A defective power supply: Replace the power supply. * A defective drive motor: Replace the motor.
Why is my Clearion Water Filtration System regenerating at the wrong time?
Regeneration occurring at the wrong time in your Clearion Water Filtration System can be caused by: * The time of day being improperly set, possibly due to a power failure: Reset the time of day programming and install a 9-volt battery. * The regeneration time being set improperly: Reset the regeneration time programming.
How to fix a Clearion 300 Water Dispenser that fails to regenerate automatically?
If your Clearion Water Dispenser isn't automatically regenerating, here's what you can check: * Ensure the power supply is connected to a constant power source. * Verify the meter cable is securely reconnected. * Double-check and reset the control valve programming. * Consider replacing the power supply if it's defective. * Clean or replace the meter assembly if it's dirty or defective. * Replace the motor if it's defective.
What to do if there is excessive water in the brine tank or salty water from the Clearion 300 Water Dispenser?
If you notice excessive water in the brine tank or salty water coming from your Clearion Water Dispenser, consider the following: 1. Check the drain line for any blockages and ensure proper flow to the drain. Clean the drain line flow control button. 2. Inspect the brine valve for dirt or damage; clean or replace it as necessary. 3. Examine the injector or screen for clogs; clean or replace the injector screen. 4. Ensure the inlet pressure is adequate, with a minimum of 20 psig, to allow the injector to function correctly. 5. Reduce the brine refill time if the refill cycle is too long.
Why is my Clearion 300 Water Dispenser not using salt?
If your Clearion Water Dispenser isn't using salt, try these steps: * Check and reset the control valve programming. * Clean the drain line and/or flow control button if the drain line is plugged or restricted. * Clean or replace the injector and screen if they are plugged. * Check for restrictions in the BLFC, ensure the safety float isn't stuck, and inspect the brine tank for leaks if there's no water in the brine tank. * Ensure the line pressure is at least 20 psi if the water pressure is too low. * Check brine line connections for air leaks if the brine line injects air during brine draw.
How to restore water pressure in my Clearion 300?
To restore water pressure in your Clearion Water Dispenser: * Clean or replace the pipeline if scaling or fouling of the inlet pipe is present. Consider pretreatment to prevent future issues. * Clean the resin if it's fouled. Also, consider pretreatment to prevent future fouling. * Increase the frequency of backwashing if the backwash setting is improper.
How to reduce high salt usage in my Clearion 300 Water Dispenser?
To reduce high salt usage in your Clearion Water Dispenser: * Lower the brine tank refill time if the salt setting is too high. * Lower the hardness setting or increase the days between regeneration if it's regenerating too frequently.
What causes loss of capacity in a Clearion Water Dispenser?
The causes for loss of capacity in your Clearion Water Dispenser can be: * Increased raw water hardness: Increase the hardness setting or decrease the days between regeneration. * Brine concentration and/or quantity: Keep the brine tank full of salt at all times and clean it yearly. Ensure salt is not bridged. If using a salt grid plate, make sure refill water is over it.
Essential criteria and conditions for proper unit installation.
Guidance on selecting the optimal location and specific site requirements.
Step-by-step instructions for connecting the water supply and bypass valve.
Procedures for connecting drain, brine lines, and electrical supply.
Steps to fill the system with water and remove air.
Converts nitrate and sulfate levels to calcium carbonate equivalents.
Calculates nitrate/sulfate ratio and determines resin operating capacity.
Calculates system capacity and total nitrate grains for installation.
Programs valve settings and guides manual regeneration cycles.
Instructions for filling the brine tank and performing final installation checks.
Guidelines for normal operation, maintenance, and cleaning of the unit.
Manual control for initiating or skipping regeneration cycles.
Detailed steps for programming the control valve settings.
Guide to navigating the main menu and setting basic parameters.
Explanation of home display and battery backup features.
Procedures for initiating delayed or immediate extra regeneration cycles.
Accessing and modifying advanced programming settings.
Configuring regeneration time, day override, and cycle step durations.
Configuring system capacity and Bluetooth connectivity settings.
Steps to download and install the Legacy View mobile application.
Guide to connecting the app to the water treatment valve.
Explanation of the dashboard interface and its informational fields.
Instructions for setting the unit's time using the mobile app.
Configuring the frequency of backwash cycles through the app.
Setting the desired regeneration time using the app interface.
Viewing and resetting system status and historical data.
Initiating regeneration cycles directly from the app interface.
Essential preliminary steps before performing any servicing operations.
Step-by-step guides for replacing key valve components and seals.
Steps for servicing or replacing the injector and screen.
Instructions for removing, cleaning, or replacing the water meter.
Procedure for replacing the brine valve assembly.
Diagnosing and correcting regeneration failures and capacity loss.
Addressing issues with water quality, salt usage, and water pressure.
Troubleshooting excessive brine tank water or salty service water.
Diagnosing why the softener is not drawing or using salt.
Correcting issues causing continuous water flow to the drain.
Understanding the error code system and general diagnosis.
Troubleshooting specific control valve error codes and display issues.
Details on warranty coverage, terms, conditions, and exclusions.
Understanding warranty limitations, remedies, and the claim process.
General| Brand | Clearion |
|---|---|
| Model | 300 Series |
| Category | Water Dispenser |
| Language | English |
To Next Page
