Need help?Do you have a question about the CLIVET WSN-XIN Series and is the answer not in the manual?
Lists and describes components shown in the installation diagram.
Details on manual content and preliminary requirements for operation.
Identifies potential hazards during unit operation and installation.
Specifies the unit's intended cooling/heating water use.
Covers positioning, hydraulics, electrics, and ducting requirements.
Emphasizes periodic maintenance and warns against modifications.
Advises immediate disabling and contacting service for breakdowns.
Installer must train user on operation and maintenance procedures.
Keep manual accessible, note unit data, and identify the unit via serial number.
Guide for noting serial number and other data for assistance requests.
Procedures for checking the unit upon delivery and handling damage.
Guidelines for storing the unit according to packaging instructions.
Steps for safe handling and lifting equipment.
Steps for safely removing packaging from the unit.
Requirements for spaces around the unit for operation and maintenance.
Criteria for choosing an installation place and avoiding issues.
Diagrams illustrating correct and incorrect positioning practices.
Instructions for adjusting the air supply direction.
Management of condensate water to prevent wetting pedestrian areas.
Instructions for installing the GMX supply grille accessory.
Importance of water quality and acceptable values.
Measures to prevent freezing in cold conditions.
Use and considerations for antifreeze solutions.
Requirements for water flow rate.
Importance and installation of the flow switch.
Step-by-step procedure for water circuit operation.
Installer defines component type and position in system.
Installation and maintenance of the water filter.
Information on unit's electrical data and serial number label.
Steps for making electrical connections.
Guidelines for laying signal and data cables.
Details on power input connections and isolator switch.
Diagrams and labels for electrical panels of different sizes.
Wiring diagrams for customer connections.
Configuration of remote ON/OFF and standby operation.
Configuration of remote summer/winter modes.
Procedure for enabling a second setpoint.
General overview of start-up operations and preliminary checks.
Step-by-step sequence for unit start-up.
Checks for the refrigeration circuit, including oil and pressure.
Checks for the water circuit, including antifreeze measures.
Verification of electrical connections and voltage parameters.
Operation and checks for compressor crankcase heaters.
Checking operating voltages and unit absorption.
Configuration of the second set point for the unit.
Adjusting set-point based on external temperature.
Adjusting set-point based on ambient temperature.
Procedure for setting minimum pump speed.
Procedure for adjusting maximum fan speed.
Configuration for energy saving mode for the circulating pump.
Function to prevent pump lock due to prolonged inactivity.
Antifreeze function for the circulating pump.
Antifreeze function for the heater.
Antifreeze function for the heat pump.
Identifying operating conditions for reporting.
Information on compliance with the PED directive.
Explanation of display icons and their fixed/flashing meanings.
Description of control keys and their functions.
Navigation through menus and changing operating modes.
Steps to enter and manage the unit's stand-by mode.
Steps for controlling the unit's power ON and OFF.
How to change the unit's operating mode (Heat, Cool, Standby, DHW).
Procedure to modify water setpoints for heating and cooling.
How to view the status of unit inputs and outputs.
Steps for setting the unit's clock and date.
Procedure for silencing alarms and understanding their codes.
How to access and interpret alarm codes and states.
Procedure for resetting alarms after identifying and removing the cause.
How to view the log of recorded alarms and their details.
Procedure for resetting the alarm log.
Accessing and understanding configuration parameters.
Setting up different operating schedules for the unit.
Examples of setting up, modifying, and activating operating schedules.
Table detailing parameters for different events and schedules.
Enabling and configuring Domestic Hot Water (DHW) function.
Setting Domestic Hot Water (DHW) setpoints and hysteresis.
Scheduling for anti-legionella cycles to prevent bacteria growth.
Settings related to the Domestic Hot Water heater.
Information on the functionality of the remote control accessory.
Setting the keypad to display the ambient temperature.
Settings for ambient keyboard display and temperature compensation.
List of alarm codes, descriptions, and their types.
List of alarms specific to the electronic thermostatic driver.
Explanation of LED indicators on the inverter for status.
Detailed list of unit status codes and their descriptions.
General overview of maintenance procedures and goals.
Recommended frequency for unit inspections.
Procedures for putting the unit into standby mode for inactivity.
Checklist for regular maintenance tasks on unit controls.
Instructions for cleaning the air coil to maintain thermal exchange.
Procedures for checking water filter, pumps, compressor, fans, and drains.
Information on the Copeland scroll compressor's temperature protection.
Step-by-step guide for replacing the unit's fan.
Details and diagrams for the remote control accessory.
Installation of the serial communication module with RS485 converter.
Description and operation of the DHW module and its controls.
Installation guidelines for domestic hot water storage tanks.
Information and usage guidelines for the 2/4kW electric heater.
Description and operation of DHW systems with solar energy integration.
Electrical diagrams for the CMACSX Domestic Hot Water module.
System configuration for boiler production only.
How the system manages boiler and DHW production.
Key parameters for boiler control and setting.
Procedure for boiler taking over from heat pump based on temperature.
Diagrams illustrating boiler and valve control logic.
Information on cascading up to 4 units and automatic rotation.
Example setpoints and scheduling for summer and winter operation.
Information on heat pump and pool connection for the cabinet.
Operating parameters for cooling and heating modes.
Procedures for safely disconnecting the unit.
Guidelines for dismantling and disposing of the unit responsibly.
Information on Waste Electrical and Electronic Equipment directive.
Overview of common risk situations for people and things.
Detailed risks for electric parts, moving parts, refrigerant, and hydraulics.
Performance data for radiant panels, terminal units, and radiators.
Technical specifications for compressors, exchangers, and fans.
Technical data for the water circuit and power supply.
Table of admissible minimum and maximum water flow rates.
Sound pressure and power levels for unit operation.
Charts showing operating ranges for cooling mode.
Charts showing operating ranges for heating mode.
Dimensional drawings and specifications for sizes 21-31-41.
Dimensional drawings and specifications for sizes 51-71.
Dimensional drawings and specifications for sizes 81-91-101.
Dimensional drawings and specifications for sizes 121-131-141.
To Next Page
General
