Why does my Club Car Golf Cars vehicle pull to one side?
Your Club Car Golf Cars vehicle may pull to one side due to several reasons: * Incorrect or distorted brake pads. * Grease or brake fluid on the brake pads. * Scored or warped brake disc. * Water on the brakes. * Sticking caliper piston.
What to do if my Club Car Golf Cars brake pedal feels springy or spongy?
If the brake pedal on your Club Car Golf Cars feels soft, springy, or spongy when pressed, it could be due to: * Cracked or thin disc: Consider replacing the brake discs. * Poor quality brake fluid or water in fluid: Purge the hydraulic fluid and refill with approved DOT 5 (silicone) brake fluid. * Weak (bulging) brake hoses that expand under pressure: Check the master cylinder, brake lines, and hoses for leaks or bulges. Replace any damaged parts. * Air in the hydraulic system.
How to fix a low brake pedal on Club Car Golf Cars?
If the pedal on your Club Car Golf Cars goes to the floor, it may be due to: * Excessive clearance between the disc and brake pads. * A leak in the hydraulic system: Check the master cylinder, brake lines and hoses for leaks. Replace all damaged parts and bleed brake system. * Air in the hydraulic system. * A weak (bulging) brake line: Replace the worn hose. * An improperly adjusted master cylinder push rod.
Why is excessive pedal pressure required to stop my Club Car Golf Cars?
If excessive pedal pressure is required to stop your Club Car Golf Cars vehicle, it could be due to: * Grease or brake fluid on the brake discs or pads: Replace the hub or axle seal and replace the brake pads. * Glazed brake pads: Replace the brake pads. * Damaged or distorted brake pads: Replace the brake pads. * Clogged hydraulic lines: Replace brake lines as required. * Frozen master cylinder piston or bent rod: Replace master cylinder.
What causes pulsating brake pedal in Club Car Golf Cars?
A pulsating brake pedal in your Club Car Golf Cars can be caused by: * Warped or worn brake discs: Replace the brake discs. * Bent wheel: Replace the wheel. * Worn or damaged wheel bearings: Replace bearings.
Why is there noise and chatter when I apply the brakes on my Club Car Golf Cars?
Clicking or scraping sounds upon brake application in your Club Car Golf Cars can be caused by: * Bent, damaged, or incorrect brake pads: Replace the brake pads. * Worn brake pads: Replace the brake pads. * Foreign material embedded in brake pads: Replace the brake pads. * Brake discs are cracked or scored: Replace the brake discs.
What causes all brakes to drag on a Club Car Golf Cars?
If all brakes drag on your Club Car Golf Cars, it may be due to: * Binding brake pedal: Replace bushings and adjust. Also replace any bent or damaged components. * Soft or swollen rubber parts caused by incorrect or contaminated brake fluid: Replace master cylinder.
What causes decreasing brake pedal travel in Club Car Golf Cars?
Decreasing brake pedal travel in your Club Car Golf Cars can be caused by: * Sticking caliper piston: Replace the caliper.
What causes rear brakes to drag on a Club Car Golf Cars?
If the rear brakes drag on your Club Car Golf Cars, it could be due to: * Binding park brake cables: Adjust or replace cables. * Improper brake adjustment.
What causes over-aggressive braking in Club Car Golf Cars?
Over-aggressive braking in Club Car Golf Cars can be caused by: * Incorrect or distorted brake pads: Replace the brake pads.
General| Payload Capacity | 1, 500 lbs |
|---|---|
| Vehicle Load Capacity | 1, 500 lb (680 kg) |
| Engine Type | 4-cycle |
| Seating Capacity | 2 |
| Cargo Bed Capacity | 1, 000 lbs |
| Wheels | Steel |
| Standard Features | Headlights, Taillights, Brake Lights, Horn |
Explains the identification and purpose of safety decals on the vehicle.
Provides instructions for cleaning, inspecting, and maintaining safety decals.
Defines DANGER, WARNING, and CAUTION symbols, colors, and associated hazards.
Defines CAUTION without a symbol as a potentially hazardous situation causing property damage.
Introduces the manual's scope for all gasoline and diesel Carryall 1500/1700 and XRT 1550/1550 SE vehicles.
Provides spaces to record vehicle identification numbers for reference.
Introduces instrument panel controls and provides operational warnings.
Details operation of forward/reverse, accelerator, brake pedals, and park brake.
Provides a warning about the park brake's locking positions.
Explains steering adjustment and warns to ensure it's engaged.
Describes accessory outlet power and the low oil warning light.
Details fuel gauge, hour meter, headlights, and electric bed lift.
Explains diesel high-temperature warning light and coolant safety.
Emphasizes ROPS installation and seat belt use for occupant safety.
Ensures seat hinges and latches are engaged before operation.
Warns against adjusting seats while vehicle is in motion.
Lists daily checks for general parts, decals, ROPS, belts, tires, battery, and engine.
Covers pre-drive checks, brake bedding, and performance inspection.
Details starting procedures and explains all-wheel drive system operation.
Warns operators to control speed downhill and about gear shifting.
Provides warnings for servicing the cargo bed, including prop rod safety.
Covers stopping procedures, brake effectiveness after water, and hill parking.
Details dangers and warnings related to the cargo bed latch and prop rod.
Provides warnings for loading cargo, including park brake, speed on slopes, and capacity.
Warns about cargo handling, center of gravity, securing loads, and stopping on hills.
Defines occupant, cargo, trailer tongue, gross trailer, vehicle rated, and combination weights.
Provides warnings about towing, including speed, caution, avoiding public roads, and hill stops.
Details warnings for transporting on a trailer, including fuel shut-off, securing, and turning.
Warns about draining fuel when hot and fuel storage safety.
Provides storage guidelines and warns about battery charging.
Emphasizes safety for maintenance, including technician qualifications and warnings.
Outlines service intervals and stresses the importance of repairs.
Details checks for battery, wheel alignment, wiring, and connections.
Covers brake system inspection, engine checks, and air intake maintenance.
Details fuel filter replacement, decal checks, and drive belt inspection.
Illustrates lubrication points and lists recommended lubricants for various components.
Details how to check brake fluid level and specifies DOT 5 fluid.
Recommends using only DOT 5 (silicone) brake fluid.
Explains daily oil checks, pressure, and cautions against overfilling.
Details procedures for draining oil and replacing the oil filter.
Specifies oil amounts for engine changes and cautions against overfilling.
Guides on oil viscosity selection and introduces gearcase lubrication.
Details procedures for checking and changing lubricant levels in gearcases.
Explains coolant level check and warns about pressurized tanks.
Covers air intake system cautions and guides on air filter replacement.
Details fueling safety, including dangers of fire and cautions on fuel types.
Discusses biodiesel fuel, its cautions, and draining water from the fuel filter.
Covers battery dangers, acid hazards, and safety precautions for servicing.
Details safety precautions and cautions for jump starting the vehicle.
Provides procedures for cleaning the vehicle and notes on waste water disposal.
Covers accessory warnings, cautions, and electric winch safety.
Details mud tire operation warnings and subsequent owner registration.
Details engine, fuel, electrical, and brake systems specifications.
Provides vehicle dimensions, weight, and capacity information.
Lists liquid capacities for various fluids and recommended tire pressure.
Outlines the limited warranty, its coverage, exclusions, and voiding conditions.
Details warranty remedies, disclaimers, and how to make a claim.
Covers federal and California emissions warranty coverage and periods.
Outlines owner responsibilities for maintenance and warranty claims.
To Next Page
