GREAT BRITAIN • CUSTOMER SERVICE tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk postal 10 – 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
Ver. 20160526
Wireless Wall Switch,
2-gang
Art.no 36-6364 Model 50078
Please read theentire instruction manual before using theproduct and
then save it for future reference. Wereserve theright for any errors in
text or images and any necessary changes made to technicaldata.
Intheevent of technical problems or other queries, please contact our
Customer Services.
Things to consider:
• Other wireless equipment using thesame frequency band can
reduce thetransmissionrange.
• Therange of all wireless equipment depends on thetype of
obstacles located between thetransmitter and thereceiver
(e.g. aconcrete wall will interfere with thesignal more than
aplasterboard wall).
If you experience problems, try thefollowing:
• Turn off any other existing wireless equipment to check whether
this is thecause of theproblem.
• Reposition thewireless equipment, shorten thedistance between
thetransmitter and thereceiver or reduce thenumber of obstacles
(walls, furniture,etc.) betweenthem.
Installation
5. Fasten thepush buttons back
onto theswitch module.
Care and maintenance
• Clean theexterior of thewall switch by wiping it with adampcloth.
Useonly mild cleaning agents, never solvents or corrosive chemicals.
• Remove thebattery and store thewall switch out of reach of
children if it is not to be used for alongtime.
Changing the battery
1. Remove thepush buttons from theswitch module.
2. Remove theold battery and insert anew one (1×CR2032).
Insertthebattery with the (+) facingyou.
3. Refit thepush buttons.
Troubleshooting guide
Thewall switch
does notwork.
• Check thebattery and replace it if necessary.
• Is thewall switch paired with thereceiver as
describedabove? Trypairing themagain.
• Check that thedevice (e.g. light) which is
connected to thereceiver is switched on and
not faulty.
• Is thewall switch too far from thereceiver?
• Is thesignal being blocked by furniture or
furnishings?
Responsible disposal
1. Remove thepush
buttons and frame from
theswitch module.
3. Remove theplastic tab
to activate thebattery.
2. Mount theswitch module in
thedesired location using
theincluded screws. Note: Itis
important that theswitch is theright
way up, refer to theUP mark on
theswitch.
4. Fasten theframe back
onto theswitch module.
Alignthenotches in theframe with
thelugs on themountingplate.
Operating instructions
Pairing the switch with a receiver
1. Make sure that thereceiver that you are
going to use thewall switch with is ready
to be paired (refer to theuser manual of
thereceiver).
2. Switch thewall switch to [ ON ].
Operating a dimmer receiver
If thereceiver you are using is dimmable, you can use thewall switch
to dim thelight connected to thereceiver. Whattodo:
1. Switch thelight on by pressing [ ON ] on thewall switch.
2. Press [ ON ] on again to cause thelight level to alternately increase
and decrease.
3. Press [ ON ] once again when thedesired light level has been reached.
Deleting a receiver from the remote control
1. Make sure that thereceiver that you wish to delete from thewall
switch is in thecorrect mode for removing devices (refer to
themanual of thereceiver).
2. Switch thewall switch to [ OFF ].
This symbol indicates that this product should not be
disposed of with general householdwaste. Thisapplies
throughout theentire EU. Inorder to prevent any
harm to theenvironment or health hazards caused by
incorrect waste disposal, theproduct must be handed
in for recycling so that thematerial can be disposed of
in aresponsible manner. Whenrecycling your product,
take it to your local collection facility or contact
theplace of purchase. Theywill ensure that theproduct
is disposed of in anenvironmentally sound manner.
Specifications
Frequency 433.92 MHz
Range 25m
Battery 1×CR2032 (included)
To Next Page
Need help?
General