The 75 All Road is designed to work with the Cobra All Road Wireless Push-
to-Talk Button (sold separately) to communicate while wearing a Bluetooth
®
headset. It can also be a hands-free option while using the CB.
A velcro strap is included for convenient mounting.
Pairing Instructions:
1. Push and release the PTT Button to initiate the pairing process.
2. Connect to the PTT button from the All Road Handset: MENU>>BLUE-
TOOTH>>PAIR>>WIRELESS PTT>>PAIR.
3. A pop-up window displays "Pair to Wireless PTT" when in range.
4. The wireless PTT button will automatically pair to the 75 All Road CB.
NOTE: Only the All Road Wireless PTT Button will work with the 75 All Road CB
for a handsfree or remote PTT solution.
Questions or Need Help? Please call Cobra Customer Care at 800-543-1608.
13
12
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
Menus
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Caution Warning
Installation
Customer
Assistance
Menus
-MENU-
TIME OUT TIMER
WX ALERT
WX ALERT SCAN
WX AUTO SCAN
VOX Level (Level 01 - 09)
VOX Level sets the trigger point for VOX. The higher the level, the
louder your voice needs to be to trigger VOX. To set the VOX level:
1. Enable VOX (see "VOX" instructions)
2. Press and hold the ENT/MENU button on the All Road
handset to active the MENU
3. Use the DOWN arrow key to select VOX LEVEL
from the
Menu Options
4.
Use the ESC button to get back to the home screen
VOX Delay (Level 01 - 09)
VOX Delay sets the transmitter ON or "hang time" after the user
stops speaking into the microphone. This setting is measured in
seconds and can be tailored to adjust the amount of time the
transmitter hangs in between speaking. The higher the setting, the
longer the hang time. To adjust VOX DELAY:
1. Enable VOX (see "VOX" instructions)
2. Press and hold the ENT/MENU button on the All Road
handset to active the MENU
3. Use the DOWN arrow key to select VOX DELAY
from the
Menu Options
4. Adjust VOX DELAY (01 - 09) using the UP or DOWN arrow
keys
and select ENT (Enter) to select
5.
Use the ESC button to get back to the home screen
Time Out Timer (OFF - Level 10)
The transmitter Time Out Timer sets the amount of time in minutes
that the transmitter is allowed to operate continuously. This feature
helps to minimize interference to the CB channel in the event of an
unintended transmission such as a 'stuck' PTT switch. Setting Time
Out Timer:
1. Press and hold the ENT/MENU button on the All Road handset
to active the MENU
2. Use the DOWN arrow to select TIME OUT TIMER from the
Menu options
3. Adjust TIME OUT TIMER (OFF - 10) using the UP or DOWN
arrows and select ENT (Enter) to select
4. Use the ESC button to get back to the home screen
-MENU-
BLUETOOTH
VOX
VOX LEVEL
VOX DELAY
-MENU-
BLUETOOTH
VOX
VOX LEVEL
VOX DELAY
-MENU-
TIME OUT TIMER
WX ALERT
WX ALERT SCAN
WX AUTO SCAN
-MENU-
TIME OUT TIMER
WX ALERT
WX ALERT SCAN
WX AUTO SCAN
WX Alert (ON / OFF)
When WX (or Weather) Alert is enabled, it will make an alert sound
when it picks up a 1050 Hz tone from the National Weather
Service. The weather receiver must be set to an active weather
station for the 1050 Hz tone to sound. To enable/disable Weather
Alerts:
Instructions:
1.
Press the WX button on the handset to
go into Weather Mode
and select an active (local) weather station
2. Press and hold the ENT/MENU button
on the All Road
handset to active the MENU
3. Use the DOWN arrow to select WX ALERT
from the Menu
options
4. Use the UP or DOWN arrow to select ON or OFF,
press ENT
to enable
5.
Go back to CB Mode by pressing ESC until you get to the home
screen, then press the CB/WX button on the handset to change
between CB and Weather (WX) modes
WX Alert Scan (ON / OFF)
WX AUTO SCAN when enabled will look for and lock on to the
strongest weather station signal. This happens in the background
and is useful for cross-country travel. How it works: WX AUTO
SCAN locks onto a local NWS and can be accessed when you
switch over to WX mode (by press the CB/WS button on the
handset). To enable/disable Weather Alert Scanning:
1. Press and hold the ENT/MENU button
on the All Road
handset to active the MENU
2. Select WX ALERT SCAN
from the Menu Options
3. Use the UP or DOWN arrow to select ON or OFF,
press ENT
to select
4.
Press the ESC button to get back to the home scree
To Next Page
Loading...
