17
Nothing Comes Close to a Cobra
®
Operation
Mode Functions
Operation
Customer Assistance WarrantyIntroduction
Tri-Watch Set-up
•
Your microTALK
®
radio can be set up to scan three of your favorite
channels for activity.
To Program or Edit the Tri-Watch Channels:
1.
Press and hold the TRI-WATCH button from
GMRS Standby mode for two (2) seconds to
activate Tri-Watch Setup mode. The TW icon on
the display will turn ON.
2.
Press Channel Up or Channel Down button to
select the desired Tri-Watch channel.
3. Press and release TRI-WATCH button to
confirm entry.
4.
Repeat steps 2 and 3 to program the remaining
additional Tri-Watch memory channel.
5.
After programming both Tri-Watch memory
channels the radio will immediately engage
Tri-Watch mode.
The main channel number will flash to
indicate channel position.
SCAN
VOLUME
CALL
MODE
CHANNEL
MEM
ESC
TRI
WATCH
SCAN
VOLUME
CALL
MODE
SCAN
VOLUME
CALL
MODE
CHANNEL
Tri-Watch Button
Using Tri-Watch:
1.
From GMRS Standby mode, press the TRI-WATCH
button. The TW will appear in the display along with
the three channels stored in the Tri-Watch memory.
2.
The radio will scan through the three (3) Tri-Watch
memory channels.
3.
A signal on any one (1) of the three (3) channels will
stop the scan for 10 seconds to allow you to listen
to the traffic on that location.
4.
Press Channel Up or Channel Down button to
resume scanning the Tri-Watch channels or to
change the scan direction.
5.
To EXIT the Tri-Watch scan, press the TRI-WATCH
button again, and the radio will return to GMRS
Standby mode.
After the Tri-Watch scan stops to monitor a
channel, as long as you do not press any buttons
within 10 seconds, your radio will automatically
resume scanning the Tri-Watch channels
SCAN
VOLUME
CALL
MODE
CHANNEL
MEM
ESC
TRI
WATCH
SCAN
VOLUME
CALL
MODE
SCAN
VOLUME
CALL
MODE
CHANNEL
Tri-Watch Button
Channel Scan
•
Your microTALK
®
radio can automatically scan channels.
To scan channels:
1.
Press and release the Scan button until the Scan
icon and the channel numbers appear
on the display.
2.
Press and hold the Scan button to begin scanning
channels.
The radio ignores specific privacy
codes while scanning channels.
The Scan icon will continue to be displayed when
scan is on. Your radio will continue to scan all
channels and stop if an incoming transmission is
detected. Your radio will remain on that channel for
10 seconds.
During scanning (while receiving an incoming transmission),
you can choose from the following:
a.
Press and hold the Talk button to communicate on that channel.
Your radio will remain on that channel and return to Standby mode.
b.
Press the Channel Up or Channel Down button to resume
scanning channels.
c.
Press and hold the Scan button to return to Standby.
Vox
HI WX
TW DCS Scan
CTCSS Mem
BURP Power Saver
MEM
ESC
TRI
WATCH
SCAN
VOLUME
CALL
MODE
Scan Button
16
BURP
•
BURP features allows the user to expel water from inside the speaker
grille. This is useful if the radio is dropped in the water which may
become trapped in the speaker grille and muffle the audio.
To activate BURP:
1.
Press and release the MEM/ESC and Rewind
buttons at the same time.
2.
The Burp tone(s) at maximum level will sound from
the internal speaker for 8 seconds. During this
time, BURP will appear in the display.
3.
Hold the radio with the speaker grille down to help
the water drain out.
4.
After an 8-second interval, the radio will return to
standby.
MEM
ESC
TRI
WATCH
SCAN
VOLUME
CALL
MODE
CHANNEL
R
X
Vox
HI MED LO WX
TW DCS Scan
CTCSS Mem
BURP Power Saver
BURP Icon
CXT1035R_MANL_vD.indd 17-18 2/28/14 9:59 AM
To Next Page
Loading...
Need help?
General
