To Next PageTo Next Page
Need help?Do you have a question about the Comfast CF-E325N and is the answer not in the manual?
Convert a wired network to wireless WIFI signal for others to connect to the Internet.
Receive remote wireless signal and re-transmit it for wireless or web cable connections.
Access wired network from modem/switch, share wireless WIFI signal with other devices.
Receive wireless WIFI signal and convert it to a wired network for devices.
Type in IP Address, Subnet Mask, and default gateway according to your Router's network address.
Set your SSID name and select the type of encryption, then click on 'Apply'.
Open a browser, type 192.168.10.1, enter 'admin' for user name and password.
Click 'Login' to enter the AP mode interface and select the corresponding working mode.
Select 'Repeater Mode' and enter the setting interface for configuration.
Scan surrounding wireless signals, choose SSID, type password, and connect.
Click 'Function Settings', select 'Wireless Basic Parameter Settings' to modify SSID.
Select the 'Router Mode' to begin the configuration process.
Choose between DHCP, Static IP, or PPPOE connection types.
Enter ISP account username and password for PPPOE, then set SSID and wireless password.
Select 'Client Mode' and click next step to scan for wireless signals.
Find the wireless signal, type the correct password to connect.
Product supports 48V power supply; LAN port is for POE power supply interface.
Forget IP address? Set computer IP to automatic or reset device to factory default.
Ensure network cable connects to the product WAN port for PPPOE dialing.
Connect to LAN port, ensure IP is automatic or set manually in same segment.
Use high-quality wire, less than 60 meters, and original power supply for stability.
Device shows connected but no internet; ensure product connects to external network.
Default is router mode, DHCP enabled. Other modes may require reset or manual IP setup.
Equipment complies with FCC limits; reorient antenna or increase separation to fix interference.
Device complies with Part 15 of FCC Rules, subject to no harmful interference.
Antennas must be installed with 20 cm separation from all persons.
Convert a wired network to wireless WIFI signal for others to connect to the Internet.
Receive remote wireless signal and re-transmit it for wireless or web cable connections.
Access wired network from modem/switch, share wireless WIFI signal with other devices.
Receive wireless WIFI signal and convert it to a wired network for devices.
Type in IP Address, Subnet Mask, and default gateway according to your Router's network address.
Set your SSID name and select the type of encryption, then click on 'Apply'.
Open a browser, type 192.168.10.1, enter 'admin' for user name and password.
Click 'Login' to enter the AP mode interface and select the corresponding working mode.
Select 'Repeater Mode' and enter the setting interface for configuration.
Scan surrounding wireless signals, choose SSID, type password, and connect.
Click 'Function Settings', select 'Wireless Basic Parameter Settings' to modify SSID.
Select the 'Router Mode' to begin the configuration process.
Choose between DHCP, Static IP, or PPPOE connection types.
Enter ISP account username and password for PPPOE, then set SSID and wireless password.
Select 'Client Mode' and click next step to scan for wireless signals.
Find the wireless signal, type the correct password to connect.
Product supports 48V power supply; LAN port is for POE power supply interface.
Forget IP address? Set computer IP to automatic or reset device to factory default.
Ensure network cable connects to the product WAN port for PPPOE dialing.
Connect to LAN port, ensure IP is automatic or set manually in same segment.
Use high-quality wire, less than 60 meters, and original power supply for stability.
Device shows connected but no internet; ensure product connects to external network.
Default is router mode, DHCP enabled. Other modes may require reset or manual IP setup.
Equipment complies with FCC limits; reorient antenna or increase separation to fix interference.
Device complies with Part 15 of FCC Rules, subject to no harmful interference.
Antennas must be installed with 20 cm separation from all persons.
General| Wireless Standard | IEEE 802.11b/g/n |
|---|---|
| Frequency Band | 2.4GHz |
| Frequency | 2.4GHz |
| Max Data Rate | 300Mbps |
| Antenna Gain | 5dBi |
| Ports | 1 x 10/100Mbps Ethernet Port |
| Antenna | 2 x External Antennas |
| Power Supply | 5V/1A |
| Power Supply Options | Power Adapter |
| Operating Modes | AP, Repeater |
