CONCORD 107 - FUNCTION OF CONTROLS AND JACKS; Control Descriptions; Input and Output Jacks; OPERATING INSTRUCTIONS

Function
Turning
the control
to
the
left
from
Stop
posi-
tion
rewinds
the
tape
onto the supply
reel
at a
rapid
speed.
Turning
the
control
to the
right from
Stop
posi-
tion
winds
tape
from
the
supply
reel
to
the
take-up
reel.
Record
Safety
Lock
Pulling
lock
toward
the front
of the recorder,
with
the Frurction
Control in
the
Forward
position,
places
the
unit
in
the Record
mode
of operation.
Mic
I n
put
Plug
the microphone
into
this
jack
to make
a
recording.
Earphone
Jack
Pltrg
theearphone
into
thisjack
to monitorwhile
recording.
It
may
be used
for
private
listening
dtring
playback.
O
PERAT
I
NG
Threading
the
Tape
l. Place an
empty reel
on the
take-up
(right)
spin-
dle.
2. Place
a reel
of tape
on the supply
(left)
spindle.
3.
Unwlnd 14" of
tape
from
the
supply reel, hold
a
section taut
and
insert it
into
the tape
slot.
4.
Insert tlre
free
end
into
one of the slots
ln
the
take-up reel.
5.
Turn the
take-upreel a few
turns counterclock-
nrise to secure
the tapeto thereel
and to
take
up
all
slack between reels.
Microphone
Recording
1. Thread the tape.
2.
Insert the microphone
plug
into
the Mic
Input
Jack.
Turn the On-Off
switch
to On.
Turn the Speed
Selector to the
desired speed.
5. Turn
the Function
Cohtrol to Forward-
6. Pull
the Record
Safety
Lock toward the
front
of
the recorder.
1. Hold
the microphone
6 to 12 inches from
your
mouth,
speak
in a
normal manner, and
adjust
the
Volume
Control until the two halves
of
the
magic
eye are
just
closed
on the loudest
pas-
age.
Recording f
rom
a
Radio or
TV
l.
Thread the
tape.
PAGE
2
FUNCTION
OF CONTROLS
AND JACKS
Output
Jack
This
jack
may
be
used
to
ptay
a
recording
through
an
external
speaker.
Fast
Forward
With
the
Function
Control
in
the
Forward
posi-
tion,
pull
the
Fast
Forward
Lever
toward
the
front
of
the recorder.
Tape will
advance
to
a
desired
spot
at
a
rapid
speed.
To
stop
the forward
motion
of the
tape,
return
the
Function
Control
to
Stop
position.
Remote
Control
Switch
Socket
The
Remote
Control
Sudtch
plqs
into
this
soeket
and
the
operator
can
control
the
tape motion
in
play
or Record mode.
Speed Selector
Selects
deslred
speed,
either
g
g/
4
or
7
L/
2
ips.
Turn
clockwise
and
push
down for
T
I/
2
ips.
T\rrn
counterclockwise
and
lift
for
3 3rl4
ips.
I
NSTRUCTI
ONS
2. Insert
the Radio-TV-Phono patch
cord
plug
into
the
"Aux"
Input
jack.
3.
Connect
the
other
end
of the
patch
cord across
the speaker
voice
coil.
4.
T\rrn
the
Speed
Selector
to the
desired
speed.
5.
Turn the
On-Off
switch
to
Or.
6.
Turn
the
Function
Control
to
Forward.
7. Pull
the
Record
Safety
Lock toward
the
front
of
the recorder.
8.
Adjust
the
volume control until
the loudest
pas-
sage
just
closes
the twohalves
of themagic eye.
Recording
from
a
Phonograph
1.
Thread
the
tape.
2. Insert
the
Radio-TV-phono
patch
cord
plug
into
the
I'Aux"
Input
iack.
3. Connect
the
other
end
of
the
patch
cord
to
pick-
up
leads
of the
phonograph.
4.
Turn
Speed
Selector
to the
deslred
speed.
5.
Turn
the
On-Off
switch
to
On.
6. Turn
the
Function
Control
to
Forward.
7.
Pull
the
Record
Safety
lock
toward
the front
of
the recorder.
8.
Adjust
the
Volume
Control
turtil
the two
halves
of
the
magic
eye
iust
close
on the
loudest
pas-
sage.
3.
4.