What to do if my Cool Space Freezer pump motor hums but doesn't pump water?
If your Cool Space Freezer pump motor hums but doesn't pump water, there may be an obstruction in the impeller or the pump motor may have failed. Try removing any obstructions. If that doesn't work, replace the pump.
What to do if my Cool Space Freezer pump makes a loud noise?
If your Cool Space Freezer pump is making a loud noise while running, it could be due to objects in the impeller, a loose impeller, or bad pump bearings. Try removing any objects from the impeller. If the noise persists, replace the pump.
What to do if my Cool Space Freezer pump won't run but power is available?
If the pump won’t run and power is available, and the pump is functional, ensure the switch is working. Also, check that the water level is high enough to activate the low-water cut-off circuit. Replace the switch if it is not completing the circuit. Fill the water reservoir enough to activate the Low Water Shut-off switch.
Why is water leaking from the drain valve of my Cool Space CS6-50-VD Freezer?
Water leaking from the drain valve could be due to a worn washer or stem. Ensure the drain valve is closed. Replace the washer or the drain valve.
Why is water leaking from the water flow control valve of my Cool Space Freezer?
Water leaking from the water flow control valve could be due to a worn washer, a worn stem, or a loose jam nut or lock nut. Replace the water flow control valve. Tighten the jam nut.
Why does my Cool Space CS6-50-VD breaker trip when I turn it on?
The breaker might be tripping in your Cool Space Freezer due to the power cord length, the breaker rating, or a locked-up pump. Refer to page 2 for unit amperage draw and to determine the required cord gauge. Also, consider replacing the pump.
What to do if my Cool Space CS6-50-VD Freezer pump runs but does not pump water?
If the pump runs but does not pump water in your Cool Space Freezer, there might be an air lock in the outlet side of the pump, or the impeller might not be turning. Turn the unit off and on to bleed any air. If that doesn't work, replace the pump.
How to fix dry streaks in the pads of my Cool Space CS6-50-VD Freezer?
To fix dry streaks in the pads of your Cool Space Freezer, the holes in the spray bar might be blocked, or the water flow needs adjustment. Remove the spray bar, remove the plug, and clean the tube and holes. Then, open the water flow control valve.
What to do if my Cool Space CS6-50-VD Freezer pump motor will not run?
If the pump motor will not run when the switch is turned on in your Cool Space Freezer, turn the fan on to check for power. Also, check if the water level is high enough to make the low-water cut-off circuit. If the fan doesn’t start, check the breaker and cord plug-in. If the fan does start, check for power to and through the pump switch when turned on. Fill the water reservoir.
Why is my Cool Space CS6-50-VD unit overflowing?
Your Cool Space Freezer unit might be overflowing from the reservoir because the float valve is loose at the bulkhead fitting, or the water pressure is too high (over 120psi) to allow the float valve to shut off. Tighten the connections and/or replace the hose washers. Reduce water pressure by adding an inline reducer.
How to connect the unit to a water source, with warnings about water pressure exceeding 120 psi.
Details on connecting to a 20 amp, 120 volt, 60 Hz circuit and proper extension cord usage.
Instructions for starting the pump and adjusting water flow to the cooling pads.
General advice on diagnosing unit problems and a list of necessary tools for troubleshooting.
Step-by-step guides for replacing the fan motor and the water pump assembly.
Detailed description of O/I, +, -, Fan, Pump, Auto/Manual, and Timer button operations.
General| Brand | Cool Space |
|---|---|
| Model | CS6-50-VD |
| Category | Freezer |
| Language | English |
To Next Page
