9
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY.
ITS COMMERCIAL USAGE AND USAGE IN PRODUCTION
AREAS AND WORK SPACES IS PROHIBITED.
WATER SELECTION
Use tap water to fill the tank. If tap water is hard, it is
recommended to mix it with distilled water in proportion
1:1, if tap water is too hard, mix it with distilled water in
proportion 1:2 or use distilled water only.
BEFORE THE FIRST USE
After unit transportation or storage at low tem-
perature keep it for at least three hours at room
temperature before switching on.
• Unpack the garment steamer and remove all
packaging elements that can prevent proper unit
operation.
• Place the garment steamer body (8) on a solid stable
surface and assemble the telescopic stand (6) and
the hanger (1) (pic. 1, 2, 3). Install the ironing board
(pic. 4). Place the steam iron (4) on the base installed
on the telescopic stand (6).
• For vertical steaming, you can use the ironing board
(2) as an additional support with the hanger (1). To
do this, install the board (2) (pic. 5).
• Remove the protection from the iron soleplate (4), if
there is any.
• Wipe the iron soleplate (4) with a soft dry cloth.
• Wipe the iron body and the garment steamer body
with a soft cloth.
• Make sure that the voltage of the mains corresponds
to the operating voltage of the unit.
• There may be water residue in the tank, this is
normal, as the garment steamer has undergone
factory quality control.
FILLING THE WATER TANK
Note: Before filling the water tank installed in the
unit body (8) with water, make sure that the unit is
unplugged.
• Remove the water tank from the unit body (8). Open
the water inlet lid and fill the water tank (8) with water
(pic. 6).
• Close the lid. Install the water tank back to its place.
USING THE UNIT
• Place the unit on a flat, steady, heat- and moisture-
resistant surface, make sure that it is reliable and
steady. Adjust the stand (6) height.
• When you use the steam function for the first time,
wait about 50 seconds until the pump starts operat-
ing and the unit produces steam.
• After switching the unit on and during the opera-
tion you will hear characteristic sounds of a working
pump. These sounds are caused by normal opera-
tion and are not a malfunction.
• Before using the unit, iron a piece of cloth to clean
the steam ducts of the iron soleplate (4) and the
boiler. During the first operation some particles may
appear from the iron soleplate (4) openings, it is nor-
mal and not a malfunction.
• Switch the steamer on with the button (9) and let it
warm up. You will hear a sound signal, and a red indi-
cator and the display (12) will light up on the control
panel (7).
• Select the required steam supply mode on the con-
trol panel (7) with the buttons (15). The right button
(15) increases the temperature, the left button (15)
decreases it.
• There are a total of 5 levels of temperature modes
(silk, cotton, fur, linen, woolen), which will be shown
on the display (12) with the indicators (14).
• The steam temperature mode will be shown on the
display (12) as a scale with the steam supply level
indicator (13).
• Within 50 seconds the iron will reach the required
temperature and the indicator will light up green. The
unit is ready for use.
Attention! The stand (6), the iron soleplate (4) and the
steam hose (5) heat up during the operation, do not
touch the hot surfaces of the unit, take the iron by its
handle (4) only.
• Make sure that the steam hose (5) doesn’t bend and
twist during the operation.
STEAM IRONING
• Make sure that the water tank is filled with water.
• Put the iron on the base on the telescopic stand (6).
• Insert the power cord plug into the mains socket and
press the button (9). You will hear a sound signal, and
a red light indicator and the display (12) will light up on
the control panel (7).
• Select the steam intensity with button (15).
• When you hear the sound signal and the indicator on
the panel (7) glows green, you can start steaming.
• To supply steam, press the button (3).
• During intervals in operation place the iron on the base
on the telescopic stand (6); before setting the iron on
the base wait till the steam is released completely from
the soleplate (4) openings. Make sure that no water
drops accumulate on the base; if the water drops
appear, wipe them with a soft cloth or a paper towel.
• After the use of the steamer place the iron on the base.
• Switch the unit off by pressing the button (9).
• Remove the power cord from the mains socket.
• Wait until the unit cools down completely and pour the
water out of the water tank.
VERTICAL STEAMING
• Set the ironing board (2) to the vertical position (pic. 5).
• Make sure that the water tank is filled with water.
• Put the iron on the base on the telescopic stand (6).
• Hang your clothes on a hanger and stretch the fabric
slightly with one hand.
• Connect the unit to the mains and press the button
(9). You will hear a sound signal, and a red light indi-
cator and the display (12) will light up on the control
panel (7).
• Select the steam intensity with button (15).
• When you hear the sound signal and the indicator on
the panel (7) glows green, you can start steaming.
• Holding the iron vertically and slightly tilting it forward,
press the steam supply button (3), moving the iron
downwards.
• If
you use starch, spray it on the opposite side.
Important information
• Vertical steaming is not recommended for synthetic
fabrics.
• Never steam clothes put on a person as the steam
temperature is very high, use a clothes hanger or a
To Next Page
Loading...