What to do if CooperSurgical K-Systems G185 Standard shows the wrong temperature?
If the CooperSurgical Accessories temperature is more than 0.5°C from the setpoint, the alarm will activate. Wait for the temperature to stabilize. If needed, consider moving samples to a different incubator.
Why is the O level wrong on my CooperSurgical K-Systems G185 Standard Accessories?
If the CooperSurgical Accessories measures the wrong O level, first check the mains and main fuse to ensure the system is powered on. If it is, make sure the system isn't on standby or switched off and activate the O gas regulator by setting ‘O2.r’ to on in the menu. Also, verify the gas supply, ensuring that 1.0 bar of N gas is applied. Check the O set point at ‘O2.SP’ in the menu. If the actual gas concentration is still incorrect, calibration of the gas concentration may be needed, and you should contact a service technician for assistance.
Why is the CO level wrong on my CooperSurgical Accessories?
If the CooperSurgical Accessories measures the wrong CO level, check the mains and main fuse to ensure the system is powered on. If it is, make sure the system isn't on standby or switched off and switch the system on. Then, activate the CO gas regulator by setting ‘CO2.r’ to ON in menu. Check the gas supply, ensuring that 1.0 bar of gas pressure is applied. Also, check the CO set point at ‘CO.SP’ in the menu. If the actual gas concentration is still incorrect, calibration of the gas concentration may be needed, and you should contact a service technician for assistance.
What does ‘CO2.L’ mean on CooperSurgical K-Systems G185 Standard?
If ‘CO2.L’ is shown on the CooperSurgical Accessories display, the CO gas concentration is more than ± 1% from the setpoint. Allow the system to stabilize by closing all lids.
What does ‘O2.L’ mean on CooperSurgical K-Systems G185 Standard?
If ‘O2.L’ is shown on the CooperSurgical Accessories display, the O gas concentration is more than ± 1% from the setpoint. Allow the system to stabilize by closing all lids.
What does ‘CO.Pr’ mean on CooperSurgical Accessories?
If ‘CO.Pr’ is shown on the CooperSurgical Accessories display, there is no or wrong CO gas pressure to the system. Check the CO gas supply and make sure the pressure is kept stable at 0.5-1.0 bar.
How to fix poor O gas regulation in CooperSurgical K-Systems G185 Standard?
Poor O gas regulation in CooperSurgical Accessories can be caused by open lids. Ensure all lids are closed. Also, check the grey insulation on every lid for any missing or damaged insulation.
How to fix poor CO gas regulation in CooperSurgical K-Systems G185 Standard?
Poor CO gas regulation in CooperSurgical Accessories can occur if the lids are left open, so ensure that all lids are closed. Another cause can be missing or damaged insulation on the lids, so check the grey insulation on every lid.
General| Brand | CooperSurgical |
|---|---|
| Model | K-Systems G185 Standard |
| Category | Accessories |
| Language | English |
General guidance on safe and reliable operation of the system.
Critical safety instructions to prevent serious injury or equipment damage.
Important precautions to avoid minor injury, equipment damage, or unsafe practices.
Guidance on inspecting the incubator delivery and checking contents before installation.
Instructions for correctly positioning the G185 incubator for optimal performance and ventilation.
Describes the G185 incubator's composition, including culture and warming chambers.
Details how to monitor pH externally using a fiber optic cable and special dish inserts.
Explains the use of external sensors for monitoring temperature and CO₂ levels.
Instructions for connecting and managing the CO₂ and N₂ gas supply for the incubator.
Lists common alarm messages, their display, and reasons for occurrence.
Instructions on how to adjust the temperature setpoint for the G185 incubator.
Overview of all menu items, their meanings, values, defaults, and associated buttons.
Steps to activate the communications protocol for PC data logging.
Identifies common heating issues, their causes, and troubleshooting actions.
Lists issues related to CO₂ regulation, their causes, and corrective steps.
Addresses problems with O₂ regulation, its causes, and troubleshooting actions.
Procedures for checking gas and temperature calibration to ensure correct operation.
Detailed instructions on how to perform gas calibration using a gas analyzer.
Method for validating gas levels by taking samples from individual chambers.
Comprehensive guide to calibrating temperature across all regulator zones of the incubator.
To Next Page
