Coram Showers PREMIER - User Manual

71683 00 / Issue 1 / 13
CUSTOMER CARELINE 01746 713410
Equipment needed:
Drill, 6.5mm Masonry Bit, 4.5mm & 3mm Metal Bits (general), Crosshead Screwdriver, 16mm Spanner, Spirit Level, Pencil,
Tape Measure, Masking Tape, Silicone Sealant.
Note: The screws and wall plugs supplied are for masonry walls. For lightweight walls i.e. stud partition, plasterboard etc,
use the correct type of fixings.
Please read these instructions carefully and keep for future reference.
Incorrect fitting will invalidate the guarantee.
SAFETY
●Handle glass with great care.
Although the glass is very tough, sharp impacts can damage both the glass and metal frame.
●Make sure there are no hidden pipes or cables hidden in the wall where you intend to drill.
●Wear safety goggles, shoes and appropriate clothing.
BEFORE INSTALLATION
●Check that the shower tray is level in all directions. The enclosure will not sit correctly on an uneven surface.
If uneven, the wall channels may not fit and the doors may not shut correctly.
●The enclosure should be fitted on tiled walls which are sealed with waterproof grout.
● There must be a good silicone seal between the rim of the shower tray and the wall.
●The shower tray and the enclosure must match in size. Attempting to fit the incorrect size of enclosure to
the shower tray will result in water leaks.
●Always check very carefully that components are vertical.
●To avoid damage, use the opened out packaging to build the enclosure on.
PREMIER DOUBLE SLIDING DOOR
/ SIDE PANEL
Sliding Door - Pages 2 - 8 Sliding Door & Side Panel - Pages 9 - 16

Summary

Safety Precautions

Handle Glass With Care

Handle glass carefully; sharp impacts can damage glass and frame.

Wall Drilling Safety

Ensure no hidden pipes or cables in the wall before drilling.

Personal Protective Equipment

Wear safety goggles, shoes, and appropriate clothing.

Before Installation Checklist

Verify Shower Tray Level

Ensure the shower tray is level in all directions for correct fitting.

Wall and Tray Preparation

Fit on tiled, sealed walls with good silicone seal between tray and wall.

Component Size Match

Ensure enclosure size matches shower tray to prevent water leaks.

Check Vertical Alignment

Always check that all components are vertical during installation.

Support During Assembly

Use opened packaging to support the enclosure during assembly.

Product Recycling Information

Recycle Packaging and Materials

Information on recycling packaging materials and product components at end of life.

Product Care and Usage Guidelines

Post-Installation Usage Delay

Do not use the shower for 24 hours after installation of the enclosure.

Recommended Cleaning Methods

Clean with warm soapy water; avoid bleach and aggressive cleaning agents.

Glass Coating Maintenance

Use a squeegee to remove water and debris from the glass coating.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features
5. Safety Precautions during Installation
6. Recycling Information

This document provides installation instructions and product information for the Premier Double Sliding Door / Side Panel shower enclosure.

Function Description:

The Premier Double Sliding Door / Side Panel is a shower enclosure designed for installation on a shower tray, creating a sealed showering area. It features two sliding doors for entry and exit, and can be configured with a side panel on either the right or left, offering flexibility in bathroom layouts. The sliding mechanism allows for space-saving operation compared to hinged doors. The enclosure is designed to be fitted on tiled walls with waterproof grout and requires a good silicone seal between the shower tray rim and the wall to prevent leaks.

Important Technical Specifications:

• Door Widths (X):
  • 1500mm enclosure: 1450 - 1500mm
  • 1700mm enclosure: 1650 - 1700mm
• Side Panel Widths (Y):
  • 700mm enclosure: 670 - 695mm
  • 760mm enclosure: 735 - 760mm
  • 800mm enclosure: 775 - 800mm
  • 900mm enclosure: 875 - 900mm
• Rail Lengths:
  • 1500mm Rail: PN80599
  • 1700mm Rail: PN80600
• Drill Bit Sizes:
  • 4.5mm drill bit for wall channels (groove)
  • 6.5mm drill bit for wall plugs (30mm deep)
  • 3mm drill bit for fixing wall channels/corner post to fixed panels/side panel (10mm deep)
• Screw Sizes:
  • 8 x 32mm screws for fixing wall channels to walls
  • 6 x 10mm screws for fixing wall channels/corner post to fixed panels/side panel
  • 2 x 13mm screws for fixing top rail to fixed panels
  • 12mm screws for fixed panel retainer covers
• Seals:
  • Short flipper seals (PN40308) for fixed panels (flaps on the inside)
  • Flipper seals (PN40309) for doors (flaps on the outside)
  • Magnetic seals (PN40311) for door closing edges
• Components: Includes wall channels (PN11029, PN11031), bottom rail (PN11030), top rail (PN11032), fixed panels, sliding doors, side panel, corner post, door rollers, door handles, fixed panel brackets, fixed panel retainer covers (PN80618), retainer caps (PN50370), wall channel clips (PN50359), wall channel cover strips (PN11031), corner post cover strip (PN11032), and various screws and wall plugs.
• Glass: Although tough, sharp impacts can damage it. Handle with great care. A glass coating has been applied to the product.

Usage Features:

• Sliding Door Operation: The enclosure features double sliding doors that run on top and bottom rails. The top wheels may require adjustment to ensure the doors slide freely and the magnetic seals meet evenly when closed. Adjustments are made by turning an adjuster screw under each top wheel from outside the enclosure until the doors hang vertically.
• Door Handles: Handles are fitted to the doors using allen bolts from the inside. Rubber washers must be placed between the handles and the glass to prevent damage; avoid overtightening.
• Bumpers: The doors are equipped with top and bottom bumpers. These can be adjusted by loosening a screw, moving the rubber bumper as required, and then re-tightening. Cover caps (PN4745) are then pushed into place.
• Flexible Installation: The enclosure can be assembled with the side panel on either the right or left, allowing adaptation to different bathroom layouts.
• Sealing: Silicone sealant is applied from the outside only, along the bottom of the enclosure and 50mm up the wall channels and vertical joints, to ensure a watertight seal.

Maintenance Features:

• Cleaning: Use warm soapy water and a clean cloth to clean the enclosure, then rinse off.
• Prohibited Cleaning Agents: Do NOT use bleach, scouring powders, solvents, or other aggressive cleaning agents, as these can damage the product.
• Glass Coating: The product features a glass coating. To maintain its effectiveness and remove water and debris, use a squeegee regularly.
• Fixings Check: Periodically check all fixings and tighten them if necessary to ensure the enclosure remains secure and stable.
• Post-Installation Wait Time: It is crucial not to use the shower for 24 hours after installation to allow the silicone sealant to cure properly.

Safety Precautions during Installation:

• Handle glass with great care.
• Ensure no hidden pipes or cables are in the wall where drilling is planned.
• Wear safety goggles, shoes, and appropriate clothing.
• Check that the shower tray is level in all directions before installation; an uneven surface will prevent correct fitting and door closure.
• The enclosure must be fitted on tiled walls sealed with waterproof grout.
• A good silicone seal is required between the shower tray rim and the wall.
• The shower tray and enclosure must match in size to prevent leaks.
• Always check that components are vertical.
• Use opened-out packaging to build the enclosure on to prevent damage.
• The supplied screws and wall plugs are for masonry walls; use appropriate fixings for lightweight walls (e.g., stud partition, plasterboard).
• When drilling, use masking tape on the wall to prevent the drill bit from slipping.
• Do not drill too deep when fixing into fixed panels or side panels.
• Two people are advised for hanging the doors to avoid damaging runners, rails, or doors.

Recycling Information:

• Packaging: Cardboard and polythene parts of the packaging are recyclable.
• End of Life: The product contains recyclable materials such as aluminium and glass. Contact your local authority for recycling information.

Coram Showers PREMIER Specifications

General

Brand	Coram Showers
Model	PREMIER
Category	Bathroom Fixtures
Language	English