Cornelius J - Page 12

J | CORNELIUSPOOLS.COM | 12775, BRAULT, MIRABEL, QC, J7J 0C4 12
3. ABOVEGROUND POOL PARTS LIST*
Count your parts before starting pool
12’ x 18’
5,60 x 3,70
12’ x 24’
7,30 x 3,70
16’ x 26’
8,00 x 4,90
16’ x 32’
9,80 x 4,90
18’ x 33’
10,00 x 5,50
18’ x 38’
11,60 x 5,50
18’ x 43’
13,40 x 5,50
A 8”(20,30 cm) Ledge #28605PEP/R86-05KR 47 3/8”
(120,33 cm)
10 10 - - - - -
A 8”(20,30 cm) Ledge #28604PEP/R86-04KR 49
9/32”(125,17 cm)
- - 12 12 - - -
A 8”(20,30 cm) Ledge #28602PEP/R86-02KR 52 5/8”
(133,67 cm)
- - - - 12 12 12
A 8”(20,30 cm) Ledge #28609PEP/R86-09KR 32 5/8”
(82,87 cm)
4 8 8 12 12 16 20
B Upright Post 7”(18 cm) #7RCSPEP52/7RCRKR52 8 8 10 10 10 10 10
C Bottom Connector #7RBC 8 8 10 10 10 10 10
D Top Connector #21001 8 8 10 10 10 10 10
E Cap (2 piece round) #8CAP 14 18 20 24 24 28 32
F Cap Extension (1 piece oval) #8621 6 10 10 14 14 18 22
G Foot Collar / Round Extension #8620 16 16 20 20 20 20 20
I TopTrack #6101-00 10 10 12 12 12 12 12
J BottomTrack #R104-00 10 10 12 12 12 12 12
K Oval Track #6101-31 4 8 8 12 12 16 20
M Buttress Top Connector #568UBC 6 10 10 14 14 18 22
N Buttress Post #7005SG52 6 10 10 14 14 18 22
O Buttress Angle Brace #7006 6 10 10 14 14 18 22
P Buttress Bottom Brace #7007GV 6 10 10 14 14 18 22
Q
Wall Bearing Plate #7009 2 4 4 6 6 8 10
S Inner Combing 56”(142,24 cm) #12020 11 13 16 18 19 21 23
T Self Tapping Screws #14,1” (2,54 cm) 158 194 220 256 256 292 328
U 1/2”x 1”(12,70 mm x 2,54 cm) Bolt,Nut, Washer 12 20 20 28 28 36 44
V Strap Hardware 1/4” #20 x 5/8”(6,35 mm x 15,88 mm) 48 80 100 140 140 180 220
V Buttress Hardware 1/4” #20 x 5/8”(6,35 mm x 15,88 mm) 40 72 72 104 104 136 168
W Self Tapping Screws #12,1/2”(25,28 mm) 28 36 40 48 48 56 64
X Tension Strap 55 3/16”(140,18 cm) #18008 9 15 - - - - -
X Tension Strap 54 1/4”(137,80 cm) #18007 - - 20 28 - - -
X Tension Strap 60”(152,40 cm) #18009 - - - 28 36 44
Y Liner 1 1 1 1 1 1 1
Z SteelWall (includes joiner screws) (v) 1 1 1 1 1 1 1
AA Cap Spacers #6522
Installation Sheet
Safety Stickers
Note:
Top and BottomTrack # indicate proper #6101-00 (i)
radius by inserting code in place of -00 #R104-00 (j)
NOTE (aa): If steel ledge is used, cap spacer is not required.
14
1
2
-28
-28
18
1
2
-28
-28
20
1
2
-29
-29
24
1
2
-29
-29
26
1
2
-30
-30
28
1
2
-30
-30
32
1
2
-30
-30