This document describes a twin-tub washing machine, designed for household use. It features separate tubs for washing and spinning, offering flexibility in laundry care.
Function Description:
The washing machine is designed to clean clothes through a washing cycle and then remove excess water through a spin-drying cycle. It allows users to control both the wash and spin timers, as well as select the wash mode (Normal or Gentle) and water level (High, Middle, Low) based on the garment type and quantity. The machine is equipped with a pulsator in the wash tub to agitate clothes and a spin dryer tub for efficient water extraction. A drain function is also included to remove water after washing.
Important Technical Specifications:
While specific power consumption and motor specifications are not detailed, the manual provides guidelines for water level and corresponding washing powder capacity:
- Water Level / Washing Powder Capacity:
- High: 40-57g
- Middle: 30-48g
- Low: 25-40g
- Washing Time:
- Gentle mode (Silk or floss clothing): 3-5 minutes
- Normal mode (Linen or very dirty garments): 5-9 minutes or 9-15 minutes (depending on dirtiness)
- Spin Time:
- Shirt (synthetic fibre): 1-2 minutes
- Underwear: 3-5 minutes
- Work clothes: 5 minutes
- Installation Clearance: The washing machine should be installed at least 5 cm (2 inches) away from the wall.
- Water Temperature Limit: When using warm water, ensure it does not exceed 122°F (50°C).
Usage Features:
- Twin-Tub Design: Separate wash and spin tubs allow for simultaneous or sequential washing and spinning, providing flexibility.
- Control Knobs:
- Wash Timer Knob: Sets the duration of the wash cycle.
- Wash Selector Knob: Allows selection between "Normal" and "Gentle" wash modes, and also serves as the "Drain" selector.
- Spin Timer Knob: Sets the duration of the spin-dry cycle.
- Water Inlet Port: For connecting the water intake pipe to fill the wash tub.
- Drain Hose: For draining water from the machine.
- Water Level Selection: Users can choose between High, Middle, and Low water levels to match the quantity of garments, with a recommendation to use middle or high positions for better results.
- Garment Preparation:
- Before washing, users are instructed to remove coins, nails, or other objects from garments.
- Chemical reagents should not be put into the washing machine.
- Clothes should be turned inside out before washing.
- Using a laundry bag (not included) for delicate items is recommended.
- Washing Process:
- Connect the intake pipe to the water spigot.
- Plug in the power cord.
- Put down the drain pipe.
- Place garments into the wash tub and add washing powder.
- Choose the appropriate water level based on garment quantity (High, Middle, Low).
- Select the wash mode (Normal or Gentle) based on garment material and dirtiness.
- Set the wash timer. The machine will begin to work once the water reaches the selected level.
- Draining Process: After washing, turn the selector switch to the "Drain" position to empty the water.
- Spinning Process:
- Put garments into the spin tub after draining.
- Cover the inner and outer spin lid of the spin tub.
- Choose the appropriate spin time based on the garment type (e.g., Shirt, Underwear, Work clothes). The machine will then begin to spin.
- Safety Features:
- Spin Dryer Safety Cover: Users are advised to use the safety cover to prevent clothes from coming out of the spin tub.
- Child Safety: Never put hands into the spin tub while it is working, especially for children.
- Installation Stability: The machine must be installed on a firm and smooth ground.
- Prohibited Substances: Never use gasoline, alcohol, or other organic solvents to clean the machine.
- Electrical Safety: Do not pour water on the switch.
- Environmental Restrictions: Do not install in a bathroom or on inclined ground.
Maintenance Features:
- After Washing:
- Remove the plug.
- Turn off the spigot.
- Hang up the drain pipe.
- Clean the spin tub.
- Open the plastic cover to dry the tub.
- Lint Filter Cleaning:
- The lint filter should be cleaned after every washing cycle.
- To clean, remove the lint filter and put it in water.
- After cleaning, install the filter back at the bottom of the wash tub.
The manual emphasizes the importance of reading all instructions carefully, retaining them for future reference, and contacting customer service for any missing or damaged parts. It also advises assembling the product near its intended use area to avoid unnecessary movement.
To Next Page
Need help?
General
