Coviden Kangaroo Joey - User Manual

Normal Operation "Feed Only Set" Directions For Use
Battery Operation
Unplugging the pump from the AC line will automatically place the pump on battery power. To
recharge the battery, plug the pump into an AC wall outlet. Pump will automatically begin charging.
General Instuctions
1. Fill or spike feeding container prior to setting up pump.
2. Turn pump on - Press
Power button in lower right-hand corner.
3. In order to achieve proper accuracy, the fluid line in the feeding set bag must be 6
inches above the top of the feeding pump, when initiating the feeding cycle.
4. Select
"Keep Settings" or "Clear Settings" (for day to day use with the same feeding
regimen the
"Keep Settings” option should be selected).
5. Load the Feeding Set per diagram.
Do not overstretch the tubing.
Priming the Pump
1. Press "Prime Pump" to access the pump priming options.
2. Press
"Auto Prime" to automatically prime the pump set. The pump will quickly prime the
feed line and stop the formula before reaching the end of the feeding line.
3. Press the
"Hold To Prime Feed" menu selection to manually top off the line.
4. Press
"Done".
Setting the Feed Rate
1. Select "Adjust Feed" then "Feed Rate" use the buttons on the left to program the pump
from 1 to 400 in increments of 1ml. Select
"Enter" when desired rate is set.
Note the Volume To Be Delivered "VTBD" Rate - is an Optional Feature
• Only use the “VTBD” option if you want the pump to stop and alarm once a set amount of
formula is delivered.
• Select "Run" you will notice a small drop scroll down the screen when running.
Re-Priming the Pump After the Feed Bag Empties
1. A pump set bag that has been emptied will trigger the Feed Error screen. In this condition the
pump set bag can be refilled to continue the feeding, but only after the pump set has been re-primed.
2. Disconnect the feeding line from the patient.
3. Refill the bag.
4. Press
"Continue" to begin the pump running.
5. Press
"Hold", then press "Adjust Settings", then press "Prime Pump".
6. Press
"Hold To Prime" to prime the line. (Do Not Use Auto Prime)
7. Press
"Done", then select "Run"
To Change Rate or Clear Volume
1. Select "Hold".
2. Select
"Clear Vol Fed" to clear the volume.
3. Select
"Adjust Settings" to adjust all settings.
4. Select
"Run" to return to normal operations.
Pump sets should not be reused after 24 hours of initial usage.
t
t
t
t
t
t
t
t t
t
t
t
t
t
t
t
t
t
t
t
t
t
Enteral Feeding Pump
Kangaroo Joey
™

Summary

Normal Operation Feed Only Set Directions For Use

Battery Operation

Explanation of pump operation on battery power and charging procedures.

General Instructions

Basic setup and operational steps for the enteral feeding pump.

Priming the Pump

Step-by-step guide for priming the feeding set and pump.

Setting the Feed Rate

Instructions for programming the pump's feeding rate.

Re-Priming the Pump After the Feed Bag Empties

Procedure for re-priming the pump when the feed bag is empty.

To Change Rate or Clear Volume

Guidance on adjusting the feeding rate or clearing the fed volume.

Troubleshooting Guide

Hold Error

Troubleshooting steps for pump being in HOLDING mode for over 5 minutes.

Flow Error

Diagnosing and correcting occlusions in the pump-patient line.

Feed Error

Resolving issues related to an empty or occluded feed bag line.

Pump Set Dislodged

Steps to address a pump set that is not properly loaded.

Battery Low

Actions to take when the pump's battery charge is too low.

Rotor Error

Troubleshooting pump set tubing loading on the rotor.

System Error

General error resolution, including contacting customer service.

Coviden Kangaroo Joey Specifications