24
2) Poolchemicalsweresplashedontothegrill(chlorineandacidwillcauseveryquickproblems)andtheunit
wasnotcleanedoffquickly
3) Hardwaterfromsprinklers(chlorineinthewater)wasallowedtositontheunit
4) Saltfromtheoceanair/waterwasallowedtorestuponthegrillforaprolongedperiodoftimebeforebeing
cleaned(beachownersmustbediligentinmaintainingtheiroutdoorstainlessequipment)
5) Dust,orrust,fromothermetalsfounditwaysontothegrillandwasleftonforanextendedperiodoftime.
6) Organic matters (suchascertain types of food) might have gotten onto thesurface of the grill and it was
thencovered.Withhighhumidityandlowoxygen,corrosionwillstarttotakeplace.
7) Sprays and cleaning solutionscontaining alkaline, lime, acid, salt might have been left on the grill surface
un‐dried.
8) Nostainlesssteelpolishwaseverusedafteroneoftheabovementionedactstookplace.
WaystoAvoidRustonyour Grill:
1) Always purchase a Coyote Grill cover for your unit. This will ensure that your cover is correct fit and
breathable,whileprovidingtheprotectionneededtokeepallothercontaminantsoffofthesurface.
2) Wheninstallingtheunit,makesuretokeeptheunitcoveredwhenanymasonryworkisbeingperformed.If
anymortarordustdoescome intocontactwiththestainless,makesure towipeitoffassoon aspossible
anduseastainlesssteelpolishimmediatelyafterwards.
3) Positionyourgrillawayfromareasthatcanreceivewatersplashfromapoolorhottub.
4) Donotstorepoolchemicalsinyourislandorislandcabinets.
HowtoRemoveScratchesfromyourStainlessSteel:
Ifyoursituationisalittlemoreseriousandyouhaveobtainedscratchesinyourequipment,thenyouwillneed
to purchase a “stainless steel scratch kit.”These kits are popular in retail stores but can be easier to obtain
online.Averypopularoneiscalled“Scratch‐B‐Gone.”Withthesekits,youwillnotpolishtheunituntilyouare
donere‐scratchingtheentireproductyouareworkingon.Withascratchkit,thegoalistoliterallyre‐scratchthe
entiresurface, so thattheoriginalgrainsare replaced by your new scratched‐ingrains.With this practice, you
mustbewillingtodotheentiresurfaceasyouwillnoticeastartandstoppoint.Also,becarefultopayattention
to your rolled or finished edges asthese scratch kits will ruin this finish. After you have used the kit, you will
wanttofollowitupwithagoodstainlesspolish(asmentionedprior)andthenadrytowelforafinalwipedown.
HOWTOCHANGETHELIGHTBULBS
1. Removethescrewholdingthebulblens.
2. Reach in using your fingers only, grip the two outside edges of the light bulb, do not grip the top or
bottom of the bulb, as it might break. Pull the bulb straight out, so that the two electrode wires are
completelyremovedwithbulb.Placebulbintrash.
3. When installing the new halogen bulb be sure to use a clean cloth or paper towel to ensure the
longevityofthebulb.
4. Insert the new bulb using your clean cloth and gently snap it into position. Wipe off any fingerprints
and/orgreasethatmayhavetransferredtothebulb.
5. Re‐installthebulblensandcover
6. Fliptheswitchontochecklights.
To Next Page
Loading...
