Craftsman 247.203773 - User Manual

Craftsman 247.203773

68 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Operator’s Manual

T1200 LAWN TRACTOR

420cc, Variation Speed

42” Deck

Model No. 247.203773

For answers to your questions about

this product, call:

1-888-331-4569

Craftsman Customer Hot Line

This product has a low emission engine which operates differently

from previously built engines. Before you start the engine, read and

understand this Operator’s Manual.

• Espanol, P. 34

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

Visit our website: www.craftsman.com

CAUTION

Before using this equipment,

read this manual and follow

all safety rules and operating

instructions.

Form No. 769-09487B

(December 9, 2014)

Table of Contents

Questions and Answers

C
Catherine MartinezSep 12, 2025
Why is my Craftsman Lawn Mower not mulching grass?
- C
  Christopher DickersonSep 12, 2025
  If your Craftsman Lawn Mower isn't mulching grass properly, consider these potential causes: * The engine speed might be too low. Place the throttle in the FAST (rabbit) position. * The grass might be wet. Avoid mulching when the grass is wet. * The grass might be excessively high. Mow once at a high cutting height, then mow again at the desired height or make a narrower cutting swath. * The blade might be dull. Sharpen or replace the blade.
D
Dylan BrownAug 27, 2025
What causes an uneven cut with a Craftsman 247.203773?
- R
  reyesjesseAug 27, 2025
  If your Craftsman Lawn Mower is producing an uneven cut, you should first perform a side-to-side deck adjustment to ensure it is leveled correctly. Next, check the blade; sharpen or replace it if it's dull. Finally, verify that the tire pressure is consistent in all four tires.
D
David SimmonsAug 27, 2025
What to do if Craftsman 247.203773 Lawn Mower engine runs erratically?
- C
  Corey FloresAug 28, 2025
  If your Craftsman Lawn Mower engine is running erratically, it could be due to several reasons. First, check if the choke is activated and deactivate it. Next, ensure the spark plug wires are securely connected. A blocked fuel line or stale fuel could also be the culprit; in this case, replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. Additionally, check if the vent in the gas cap is plugged and clear it, or replace the cap if damaged. Water or dirt in the fuel system can also cause this issue, so drain the fuel tank and refill with clean, fresh gasoline. Lastly, a dirty air cleaner can lead to erratic engine performance, so replace the air cleaner paper element or clean the foam pre-cleaner if your mower is equipped with one.
B
boydlauraAug 29, 2025
How to fix uneven cut with Craftsman Lawn Mower?
- J
  Jason MartinezAug 29, 2025
  An uneven cut with your Craftsman Lawn Mower can be caused by several factors. First, the deck might not be leveled properly, so perform a side-to-side deck adjustment. A dull blade can also contribute to an uneven cut, so sharpen or replace the blade. Finally, check the tire pressure in all four tires, as uneven tire pressure can also cause this issue.
J
James StewartAug 30, 2025
What to do if Craftsman 247.203773 Lawn Mower engine idles rough?
- K
  Krista PerezAug 31, 2025
  If your Craftsman Lawn Mower engine idles rough, it could be due to a spark plug issue. The spark plug might be fouled, faulty, or have a gap that's too wide. Try replacing the spark plug and setting the correct gap. Another potential cause is a dirty air cleaner. In this case, replace the air cleaner element and/or clean the pre-cleaner.
E
Erik VazquezNov 22, 2025
Why won't my Craftsman Lawn Mower start?
- M
  Michael WalkerNov 22, 2025
  If your Craftsman Lawn Mower engine fails to start, there are several potential causes: * The PTO/Blade Engage lever might be engaged. Ensure it is in the disengaged (OFF) position. * The parking brake might not be engaged. Engage the parking brake. * Spark plug wires might be disconnected. Connect the wires to the spark plugs. * The Throttle/Choke control lever might not be in the correct starting position. Place it in the FAST position. * The choke might not be activated. Move the Throttle/Choke lever into the Choke position. * The fuel tank might be empty or contain stale fuel. Fill it with clean, fresh gasoline (less than 30 days old). * The fuel line might be blocked. Replace the fuel line and fuel filter. * The spark plugs might be faulty. Clean, adjust the gap, or r...
J
James PeckSep 22, 2025
What to do if my Craftsman 247.203773 has excessive vibration?
- M
  Michael FieldsSep 22, 2025
  If your Craftsman Lawn Mower is vibrating excessively, tighten the blade and spindle first. If the vibration continues, inspect the cutting blade for damage or bending and replace it if necessary.
E
Evan HughesNov 20, 2025
Why Craftsman 247.203773 engine fails to start?
- S
  Susan GutierrezNov 21, 2025
  Your Craftsman Lawn Mower engine might fail to start due to several reasons: * The PTO/Blade Engage lever might be engaged: place it in the disengaged (OFF) position. * The parking brake might not be engaged: engage the parking brake. * Spark plug wires might be disconnected: connect the wires to the spark plugs. * The throttle/choke control lever might not be in the correct starting position: place the lever into the FAST position. * The choke might not be activated: move the throttle/choke lever into the Choke position. * The fuel tank might be empty or contain stale fuel: fill the tank with clean, fresh gas (less than 30 days old). * The fuel line might be blocked: replace the fuel line and fuel filter. * The spark plugs might be faulty: clean, adjust the gap, or replac...
K
Karen OwenSep 10, 2025
Why Craftsman Lawn Mower engine hesitates at high RPM?
- K
  Kayla StanleySep 12, 2025
  If your Craftsman Lawn Mower engine hesitates at high RPM, it could be due to the spark plug gap being too close. Remove the spark plug and reset the gap.
K
Kimberly BanksSep 7, 2025
What causes excessive vibration in Craftsman Lawn Mower?
- T
  Timothy SosaSep 7, 2025
  Excessive vibration in your Craftsman Lawn Mower may be caused by a loose or unbalanced cutting blade. Try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, requiring replacement.

Craftsman 247.203773 Specifications

General

Brand	Craftsman
Model	247.203773
Category	Lawn Mower
Language	English

Related product manuals

Preview: Craftsman T1200 247.203770

Craftsman T1200 247.203770

Craftsman 247.20377 series

Craftsman 247.20370

Preview: Craftsman 247.203791

Craftsman 247.203791

Preview: Craftsman 247.203721

Craftsman 247.203721

Craftsman 247.203724

Preview: Craftsman 247.203750

Craftsman 247.203750

Preview: Craftsman T1000 247.203701

Craftsman T1000 247.203701

Preview: Craftsman T1600 247.203743

Craftsman T1600 247.203743

Preview: Craftsman T1400 247.203734

Craftsman T1400 247.203734

Preview: Craftsman T1600 247.203744

Craftsman T1600 247.203744

Preview: Craftsman T1200 247.203722

Craftsman T1200 247.203722