Craftsman 247.25002 - User Manual

Questions and Answers

E
Emily StuartAug 10, 2025
What to do if Craftsman 247.25002 engine runs erratically?
- H
  hubbardkelseyAug 10, 2025
  If your Craftsman Lawn Mower engine is running erratically, here are a few things to check: * Make sure the electric choke is working properly. * Check the spark plug wire to ensure it is connected and tightened. * Look for a blocked fuel line or stale fuel. Replace the fuel line and fill the tank with clean, fresh gasoline. * See if the vent in the gas cap is plugged; clear it or replace the cap if damaged. * Check for water or dirt in the fuel system; drain the fuel tank and refill with clean, fresh gasoline. * Inspect the air cleaner; if it's dirty, clean or replace the air cleaner paper element or clean the foam pre-cleaner.
O
Olivia HodgeAug 14, 2025
Why is my Craftsman 247.25002 Lawn Mower engine overheating?
- D
  Douglas MorenoAug 14, 2025
  Your Craftsman Lawn Mower engine could be overheating because the engine oil level is low. Fill the engine with the proper amount and type of oil. Another possible reason is restricted airflow. Clean any grass clippings and debris from around the engine’s cooling fins and blower housing.
K
kevindyerAug 19, 2025
Why Craftsman 247.25002 Lawn Mower engine hesitates at high RPMs?
- A
  amberblackSep 12, 2025
  If your Craftsman Lawn Mower engine hesitates at high RPMs, it might be because the spark plug gap is set too close. Remove the spark plug and adjust the gap.
H
holly67Aug 23, 2025
How to fix poor idling on a Craftsman Lawn Mower?
- S
  sara75Aug 23, 2025
  Poor idling in your Craftsman Lawn Mower could be due to a fouled spark plug; replace the spark plug and adjust the gap. Another potential cause is a dirty air cleaner; clean or replace the air cleaner element and/or clean the pre-cleaner.
M
Michael JohnsonAug 27, 2025
Why does my Craftsman 247.25002 have an uneven cut?
- M
  Michael WrightAug 27, 2025
  An uneven cut with your Craftsman Lawn Mower can occur if the deck is not leveled properly; perform a side-to-side deck adjustment. It could also be due to a dull blade; sharpen or replace the blade. Finally, check for uneven tire pressure in all four tires.
M
Mark HansenAug 31, 2025
What to do if Craftsman 247.25002 has excessive vibration?
- A
  Anita PowersAug 31, 2025
  If your Craftsman Lawn Mower is experiencing excessive vibration, it could be due to loose or unbalanced cutting blades. Tighten the blade and spindle, and balance the blade. Another cause could be a damaged, dull, or bent cutting blade, in which case you should replace the blade.
B
Bruce RobersonNov 5, 2025
Why does my Craftsman Lawn Mower engine fail to start?
- J
  Jennifer BarnesNov 5, 2025
  Your Craftsman Lawn Mower engine might fail to start due to several reasons: * The PTO/Blade Engage knob might be engaged; if so, place it in the disengaged (OFF) position. * The parking brake might not be engaged; engage the parking brake. * The spark plug wire might be disconnected; connect the wire to the spark plug. * The throttle control lever might not be in the correct starting position; place the throttle lever to the FAST position. * The fuel tank might be empty or contain stale fuel; fill the tank with clean, fresh gas (less than 30 days old). * There might be a blocked fuel line or fuel filter; consider replacing the fuel line or fuel filter. * The spark plug might be faulty; clean, adjust the gap, or replace the plug. * The engine might be flooded; crank the en...