Craftsman 247.25000 - User Manual

Other manuals for Craftsman 247.25000

Installation Manual2 pages

Questions and Answers

M
Michelle WilsonAug 4, 2025
Why is my Craftsman 247.25000 Lawn Mower engine running erratically?
- Z
  zcookAug 4, 2025
  If your Craftsman Lawn Mower engine runs erratically, it could be due to several reasons. First, check if the choke is activated and deactivate it. Ensure the spark plug wires are securely connected. A blocked fuel line or stale fuel can also cause this issue; replace the fuel line, use fresh gasoline, and replace the fuel filter. The vent in the gas cap might be plugged, so clear it or replace the cap if damaged. Water or dirt in the fuel system can also be a factor; drain the fuel tank and refill with fresh gasoline. Lastly, a dirty air cleaner can cause erratic running, so replace the air cleaner paper element or clean the foam pre-cleaner, if your mower has one.
R
Russell WeberAug 9, 2025
What causes an uneven cut with my Craftsman 247.25000?
- A
  Anna CoffeyAug 9, 2025
  If your Craftsman Lawn Mower is giving an uneven cut, it might be because the deck isn't leveled properly; perform a side-to-side deck adjustment. A dull blade can also cause this, so sharpen or replace it. Finally, check the tire pressure in all four tires, as uneven pressure can contribute to an uneven cut.
K
Kelly TranAug 14, 2025
What to do if my Craftsman 247.25000 has excessive vibration?
- R
  Rebecca Little DDSAug 14, 2025
  If your Craftsman Lawn Mower is vibrating excessively, it could be due to a loose or unbalanced cutting blade, so try tightening the blade and spindle. Alternatively, the cutting blade may be damaged or bent, in which case you should replace it.
S
seanweeksAug 19, 2025
Why is my Craftsman 247.25000 Lawn Mower engine overheating?
- S
  Sheila TaylorAug 19, 2025
  If your Craftsman Lawn Mower engine is overheating, it could be due to a low engine oil level. Fill the crankcase with the correct amount and weight of oil. Alternatively, airflow might be restricted. Clean any grass clippings and debris from around the engine’s cooling fins and housing.
J
Jared ElliottAug 25, 2025
Why isn't my Craftsman Lawn Mower mulching grass?
- S
  sarah26Aug 25, 2025
  If your Craftsman Lawn Mower isn't mulching grass effectively, make sure the engine speed is set high by placing the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a higher cutting height, then mow again at the desired height, or reduce the cutting swath. Also, check the blade; a dull blade should be sharpened or replaced.
A
Amber PughOct 29, 2025
Why won't my Craftsman Lawn Mower engine start?
- B
  barbara18Oct 29, 2025
  If your Craftsman Lawn Mower engine won't start, several factors could be at play. First, make sure the PTO/Blade Engage lever is disengaged (OFF). Check that the parking brake is engaged. Ensure the spark plug wires are correctly connected. Position the Throttle/Choke lever to FAST, or move it to the Choke position to activate it. The fuel tank may be empty or contain stale fuel; if so, refill with fresh gasoline (less than 30 days old). A blocked fuel line could also be the culprit, requiring replacement of the fuel line and filter. Inspect the spark plugs—they may need cleaning, gap adjustment, or replacement. If the engine is flooded, crank it with the throttle in the FAST position. Check for blown fuses and replace them if necessary. Finally, ensure all safety switches are properly en...

Summary

Warranty and Product Information

Craftsman Full Warranty Coverage

Details the two, five, and lifetime limited warranty periods for various parts.

Warranty Service Contact

Provides the phone number and website for obtaining warranty service.

Product Specifications and Model Number

Lists key product specifications and provides space for model/serial numbers.

Safety Instructions

General Operation and Safety Guidelines

Covers essential safety rules for assembling and operating the machine.

California Proposition 65 Warning

Warns about chemicals in engine exhaust and battery components.

Slope Operation Safety

Provides critical guidance for operating the tractor safely on inclines.

Hazard Warnings: Children, Towing, and Fuel

Addresses specific safety concerns regarding children, towing, and gasoline handling.

Maintenance and Emissions Safety

Covers general service safety, engine modification warnings, and emissions.

Safety Symbols and Warnings

Explains various safety symbols and associated warnings for safe operation.

Slope Gauge Instructions

Details how to use the slope gauge to determine safe operating limits.

Assembly Procedures

Unpacking and Required Tools

Lists crate contents, hardware pack items, and recommended tools for assembly.

Installing the Steering Wheel Assembly

Step-by-step guide for attaching the steering wheel to the tractor.

Attaching and Adjusting the Seat

Procedures for installing the seat and adjusting its position.

Steering Wheel Height Adjustment

Instructions on how to adjust the vertical position of the steering wheel.

Installing Engine Cover, Deck Chute, Bumper, and Hitch

Steps for installing the rear engine cover, deck chute, bumper, and hitch plate.

Connecting Battery Cables

Procedure for correctly connecting the positive and negative battery cables.

Gas and Oil Information

Details on recommended oil types, quantities, and fuel requirements.

Fueling and Tire Pressure

Instructions for adding fuel and setting the correct tire pressure.

Operation Guide

Control Panel Overview

Identifies key controls and indicators on the tractor's operator panel.

Understanding Tractor Controls

Explains the function and operation of throttle, ignition, pedals, and levers.

Engaging Deck and Refueling Procedures

How to use the deck lift, PTO engagement, and refuel the tractor.

Starting Engine and Safety Interlocks

Covers safety interlock systems and detailed engine starting procedures.

Driving, Stopping, and Slope Operation

Instructions for driving, stopping, and safely operating the tractor on slopes.

Mowing and Mulching Operations

Guidance on engaging the cutting blades and performing mulching operations.

Service and Maintenance

Maintenance Schedule Overview

Provides a schedule for regular service tasks based on operating intervals.

Engine Oil Service Procedures

Instructions for checking, draining, and filling the engine oil.

Oil Filter and Air Filter Service

Steps for replacing the oil filter and servicing the air filter element.

Spark Plug Service and Replacement

How to inspect, clean, gap, and replace the spark plug.

Fuel Filter Service and Engine Cleaning

Instructions for replacing the fuel filter and cleaning the engine exterior.

Cutting Deck Removal and Belt Change

Steps for removing the cutting deck and changing the deck belt.

Tire Pressure and Cutting Blade Maintenance

Guidance on setting tire pressure and maintaining the cutting blade.

Deck Adjustments and Steering Alignment

How to level the cutting deck and adjust the front wheel toe-in/out.

Seat, Brake, Belt, and Battery Maintenance

Covers seat adjustment, brake, belt replacement, muffler, and battery care.

Jump Starting, Charging, and Lubrication

Procedures for jump starting, charging the battery, and lubricating key points.

Cleaning Engine and Deck

Instructions for cleaning the tractor and using the deck wash system.

Off-Season Storage Guide

Preparing Engine for Storage

Steps to prepare the engine, including fuel stabilization or draining.

Draining Fuel and Preparing Tractor

Procedures for draining fuel and cleaning the tractor before storage.

Removing Tractor From Storage

Steps for bringing the tractor out of storage and preparing it for use.

Troubleshooting Common Issues

Engine Starting Problems

Solutions for issues when the engine fails to start or runs erratically.

Engine Performance and Overheating Issues

Troubleshooting for engine overheating, hesitation, or rough idling.

Cutting and Performance Issues

Addressing problems like uneven cuts, poor mulching, or excessive vibration.

Component Labels

Control Panel Labels

Identifies labels on the steering column and dashboard for controls.

Chassis and Cutting Deck Labels

Locates safety and identification labels on the tractor frame and cutting deck.

Parts List

Tractor Frame and Chassis Parts

Lists parts for the tractor's main frame and associated hardware.

Drive, Steering, and Wheel Components

Lists parts for the drive system, steering, wheels, and related hardware.

Controls, Seat, Battery, and Brake Components

Lists parts for controls, seat, battery, brake pedal, and related hardware.

Cutting Deck and Lift Components

Lists parts for the cutting deck, lift mechanism, and associated hardware.

Engine Ignition, Fuel, and Air Filter Components

Lists parts for engine ignition, flywheel, fuel, and air filter systems.

Engine Muffler, Starter, Shroud, and Exhaust Components

Lists parts for engine's muffler, starter, shroud, and exhaust systems.

Engine Internal, Carburetor, and Cylinder Head Components

Lists parts for the engine's internal mechanisms, cylinder head, and carburetor.

Engine Emissions Information

Emissions Durability Period and Air Index

Explains engine emissions compliance and air index ratings based on usage.

Emission Control Warranty Statement

Owners Warranty Responsibilities

Details owner's duties for maintenance and presenting the engine for service.

Warranty Provisions and Exclusions

Outlines specific warranty terms, covered parts, and reasons for exclusion.

General Emissions Warranty Coverage

Explains the scope and period of emissions warranty coverage for warranted parts.

Covered Emission Control Parts List

Lists specific parts covered under the emission control warranty.

Repair Protection Agreement

Agreement Benefits and Services

Outlines services like expert repair, product replacement, and phone support.

Purchase and Cancellation Information

Details on purchasing the agreement and refund policies.

Craftsman 247.25000 Specifications

General

Engine Brand	Briggs & Stratton
Engine Type	4-Cycle
Engine Displacement	140cc
Cutting Height Positions	6
Deck Material	Steel
Mulching Capability	Yes
Self-propelled	Yes
Starter Type	Recoil
Cutting Width	21 inches
Drive System	Rear Wheel Drive
Cutting Height	1.25 - 3.75 in.
Wheel Size	8 inches (rear)