To Next PageTo Next PageWhy is my Craftsman Lawn Mower cutting unevenly?
If your Craftsman Lawn Mower provides a poor cut with uneven cutting, the blade might be worn, bent, or loose, so replace it. Ensure the mower deck is level. Clean any buildup of grass, leaves, and trash under the mower. If the blade mandrel is bent or the mower deck vent is clogged, contact a qualified service center or clean around mandrels to open vent holes.
How to fix a Craftsman Lawn Mower that clicks but won't start?
If your Craftsman Lawn Mower's engine clicks but won't start, it could be due to a weak or dead battery, so recharge or replace the battery. Another reason could be corroded battery terminals, which you should clean. Also, check all wiring for any looseness or damage. Finally, the solenoid or starter might be faulty, so inspect and replace them if necessary.
What to do if Craftsman Lawn Mower blades will not rotate?
If the mower blades on your Craftsman Lawn Mower won't rotate, check for any obstruction in the clutch mechanism and remove it. If the mower drive belt is worn or damaged, replace it. A frozen idler pulley can also cause this issue, so replace the idler pulley. For a frozen blade mandrel, contact a qualified service center.
Why Craftsman 917.20390 battery will not charge?
If your Craftsman Lawn Mower battery won't charge, it could be due to bad battery cells, so replace the battery. Check and clean all cable connections to ensure they are secure. If your mower is equipped with a regulator, a faulty regulator could be the problem, so replace it. Similarly, a faulty alternator could be the cause, so replace the alternator.
What to do if my Craftsman 917.20390 Lawn Mower has poor grass discharge?
For poor grass discharge with your Craftsman Lawn Mower, first, ensure the engine speed is set to “FAST.” If you're moving too quickly, shift to a slower speed. Avoid mowing wet grass, and make sure the mower deck is level and the tire air pressure is correct. Check the blade; replace or sharpen it if it's worn, bent, or loose. Clean any buildup of grass, leaves, and trash under the mower. See if the mower drive belt is worn and needs replacing. Also, ensure the blades are properly installed with the sharp edge down and are the correct type for your mower. Lastly, clear any clogged mower deck vent holes around the mandrels.
Why is my Craftsman 917.20390 vibrating so much?
If your Craftsman Lawn Mower exhibits excessive vibration, the blade might be worn, bent, or loose, so replace it. A bent blade mandrel could also be the cause; tighten the blade bolt. If you notice any loose or damaged parts, contact a qualified service center to have them tightened or replaced.
Craftsman Lawn Mower headlights not working, what to check?
If the headlight(s) on your Craftsman Lawn Mower aren't working, first, check that the light switch is turned “ON.” If not, turn the light switch “ON”. If the bulb(s) or lamp(s) are burned out, replace them. A faulty light switch could also be the issue, so check and replace it if needed. Inspect the wiring and connections for any looseness or damage. Finally, check if the fuse is blown and replace it if necessary.
General| Brand | Craftsman |
|---|---|
| Model | 917.20390 |
| Category | Lawn Mower |
| Language | English |
Warnings and recommendations regarding children's safety around operating machinery.
Instructions on safe operation, clearing area, and general precautions.
Guidelines for safe operation on inclines, including turning and stopping.
Instructions for verifying the proper function of the tractor's brake system.
Instructions on operating the tractor, including braking and throttle usage.
Procedures for adjusting the mower deck for optimal cutting performance.
Safety guidelines for operating the tractor on slopes and inclines.
Explanation of the Reverse Operation System and its safe usage.
Lists causes and corrections for engine starting issues.
Lists causes and corrections for difficult engine starting.
Lists causes and corrections for reduced engine power.
Troubleshooting for mower blades failing to spin.
