EasyManua.ls Logo

Craftsman 944.363431 - User Manual

Craftsman 944.363431
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Model No.
944.363431
CAUTION:
Read and follow all
Safety Rules and In struc tions
before operating this equipment
Owner’s Manual
ROTARY LAWN MOWER
6.25 Horsepower
21" Rear Discharge
Sears Canada, Inc., Toronto, Ontario M5B 2B8

Table of Contents

Questions and Answers

  • J
    John BenderAug 8, 2025
    Why my Craftsman 944.363431 does not start?
    • H
      Heather OrtegaAug 8, 2025
      Your Craftsman Lawn Mower might not be starting due to several reasons: a dirty air filter (clean or replace it), lack of fuel (fill the fuel tank), stale or water-contaminated fuel (empty and refill with fresh gasoline). Also, check if the spark plug wire is disconnected (connect it), the spark plug is bad (replace it), the blade is loose or adapter broken (tighten or replace), the control bar is not depressed (depress it), the control bar is defective (replace it), the fuel valve is off (turn it on), the battery is weak (charge it), or the battery connector is disconnected (connect it).
  • T
    Tammy SchneiderAug 12, 2025
    Why is my Craftsman 944.363431 losing power?
    • S
      Samantha EspinozaAug 12, 2025
      Loss of power in your Craftsman Lawn Mower can happen because the mower housing or blade is dragging in the grass (raise the cutting height), you are cutting too much grass (raise the cutting height), the air filter is dirty (clean or replace it), there's a buildup of grass under the mower (clean the underside), there is too much oil in the engine (check the oil level), or your walking speed is too fast (cut at a slower speed).
  • D
    Donna LaneAug 17, 2025
    What to do if my Craftsman 944.363431 has excessive vibration?
    • N
      Nicole SpencerAug 17, 2025
      Excessive vibration in your Craftsman Lawn Mower may be due to a worn, bent, or loose blade (replace the blade and tighten the blade bolt). If that doesn't solve the problem, the engine crankshaft might be bent.
  • S
    Stephen WoodAug 20, 2025
    How to fix a poor and uneven cut with my Craftsman 944.363431?
    • W
      weberscottAug 21, 2025
      An uneven cut with your Craftsman Lawn Mower can be caused by a worn, bent, or loose blade (replace the blade and tighten the blade bolt), uneven wheel heights (set all wheels at the same height), or a buildup of grass under the mower (clean the underside of the mower housing).
  • V
    vandrewsAug 25, 2025
    Why is my Craftsman 944.363431 hard to push?
    • K
      Kelly SandersAug 26, 2025
      If your Craftsman Lawn Mower is hard to push, it could be because the grass is too high or the wheel height is too low (raise the cutting height), the rear of the mower housing or blade is dragging in the grass (raise the rear of the mower housing), the grass catcher is too full (empty the grass catcher), or the handle height is not right for you (adjust the handle height).
  • M
    Mary GonzalesAug 30, 2025
    Why is the starter rope hard to pull on my Craftsman 944.363431?
    • H
      Harold FranklinAug 30, 2025
      A hard-to-pull starter rope on your Craftsman Lawn Mower can occur if the engine flywheel brake is engaged when the control bar is released (depress the control bar before pulling the rope), the blade adapter is broken (replace the blade adapter) or the blade is dragging in the grass (move the mower to cut grass or to hard surface). Also, the engine crankshaft might be bent.
  • S
    Sarah StoneSep 2, 2025
    What to do if grass catcher is not filling on Craftsman Lawn Mower?
    • C
      Colleen BurtonSep 2, 2025
      If the grass catcher on your Craftsman Lawn Mower isn't filling, it might be due to the cutting height being too low (raise the cutting height), the lift on the blade being worn off (replace the blade), or the catcher not venting air (clean the grass catcher).

Craftsman 944.363431 Specifications

General IconGeneral
BrandCraftsman
Model944.363431
CategoryLawn Mower
LanguageEnglish

Related product manuals