Craftsman BRUSHWACKER C944.514560

Questions and Answers

A
Anthony SimonJul 30, 2025
How to troubleshoot a Craftsman BRUSHWACKER C944.514560 Trimmer that will not start?
- Z
  zosborneJul 30, 2025
  If your Craftsman Trimmer engine won't start, several factors could be at play. First, ensure the ON/OFF switch is in the ON position. If the engine is flooded, consult the Operation Section for instructions on 'Starting a Flooded Engine'. Also, check if the fuel tank is empty and refill it with the correct fuel mixture. A faulty spark plug can also prevent starting, so consider installing a new one. Finally, a dirty fuel filter or a kinked/split fuel line can block fuel flow; inspect and replace the filter or repair/replace the fuel line as needed.
M
Mrs. Susan NewmanAug 6, 2025
Why is my Craftsman BRUSHWACKER C944.514560 Trimmer smoking so much?
- K
  Katherine HayesAug 6, 2025
  If your Craftsman Trimmer engine is smoking excessively, it could be due to several reasons. First, check if the choke is partially on and adjust it accordingly. An incorrect fuel mixture can also cause excessive smoke; in this case, empty the fuel tank and refill it with the correct fuel mixture. Additionally, a dirty air filter may contribute to the problem, so clean or replace it.
S
Shannon SmithAug 13, 2025
What to do if Craftsman BRUSHWACKER C944.514560 Trimmer engine lacks power?
- L
  Lisa BlakeAug 13, 2025
  If your Craftsman Trimmer engine won't accelerate, lacks power, or dies under a load, start by checking the air filter and clean or replace it if it's dirty. Also, inspect the spark plug for fouling; clean or replace the plug and regap it.
B
bpattersonAug 22, 2025
Why is my Craftsman BRUSHWACKER C944.514560 Trimmer engine running hot?
- J
  jodi88Aug 22, 2025
  If your Craftsman Trimmer engine is running hot, the fuel mixture may be incorrect; refer to the 'Fueling Engine' section in the Operation section. Another potential cause is an incorrect spark plug; replace it with the correct one.

Summary

WARRANTY STATEMENT

SAFETY RULES

OPERATOR SAFETY

Essential safety practices for using the brushwacker safely.

UNIT;MAINTENANCE SAFETY

Safety guidelines to follow when performing maintenance on the unit.

ASSEMBLY

INSTALLING BRUSHCUTTER ATTACHMENT

Step-by-step guide to attaching the primary cutting head to the unit.

ASSEMBLY OF SHOULDER STRAP

Instructions for fitting and adjusting the shoulder strap for proper support.

ATTACHING THE HANDLEBAR

Procedure for securely attaching the handlebar to the unit.

TO RELOCATE SHOULDER STRAP CLAMP

How to move the strap clamp for optimal unit balance.

ASSEMBLY INFORMATION - TRIMMER HEAD

Key information and steps for assembling the trimmer head.

ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD

How to install the plastic shield and trimmer head assembly.

ASSEMBLY INFORMATION - WEED BLADE

Key information and steps for assembling the weed blade.

ATTACHING THE METAL SHIELD

Steps for correctly installing the metal shield for blade use.

INSTALLATION OF THE METAL BLADE

Instructions for safely installing the metal blade onto the unit.

OPERATION

KNOW YOUR TRIMMER

Familiarization with the unit's controls, switches, and components.

ON;OFF SWITCH

Explanation of the power switch function for starting and stopping.

PRIMER BULB

How the primer bulb prepares the engine for starting.

CHOKE

Using the choke lever to assist with engine starting in cold conditions.

FUELING ENGINE

Proper procedures and safety for refueling the unit.

HOW TO START YOUR UNIT

Comprehensive steps for starting the brushwacker engine.

STARTING A COLD ENGINE

Specific instructions for starting a cold or recently run-out engine.

STARTING A WARM ENGINE

Procedures for starting an engine that is already warm.

STARTING A FLOODED ENGINE

Steps to take if the engine becomes flooded.

OPERATING THE COUPLER

How to use the coupler for attaching various accessories.

REMOVING TRIMMER ATTACHMENT

Guide to safely detach cutting heads or other attachments.

INSTALLING OPTIONAL ATTACHMENTS

Steps for securely attaching optional accessories.

OPERATING POSITION

Correct posture and grip for safe and effective operation.

OPERATING INSTRUCTIONS FOR USE WITH TRIMMER HEAD

Usage guidelines for the trimmer head attachment.

TRIMMER LINE ADVANCE

Method for extending the trimmer line during use.

CUTTING METHODS

Various techniques for cutting grass and weeds effectively.

SCALPING

Technique for removing vegetation down to the ground level.

MOWING

Using the trimmer for mowing tasks in hard-to-reach areas.

SWEEPING

Using the rotating line to clear loose debris from an area.

OPERATING INSTRUCTIONS FOR USE WITH WEED BLADES

Usage guidelines for the weed blade attachment.

WHAT CAUSES BLADE THRUST

Explanation of the phenomenon of blade thrust and its dangers.

WHEN BLADE THRUST OCCURS

How to react and control the unit if blade thrust happens.

ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS

EDGER SAFETY

Specific safety precautions for using the edger attachment.

BLOWER;VACUUM SAFETY

Safety guidelines for operating blower and vacuum attachments.

CULTIVATOR SAFETY

Safety measures for using the cultivator attachment.

HEDGE TRIMMER SAFETY

Safety precautions for using the hedge trimmer attachment.

POLE PRUNER SAFETY

Safety guidelines for operating the pole pruner attachment.

SNOW THROWER SAFETY

Safety instructions for the snow thrower attachment.

MAINTENANCE

MAINTENANCE SCHEDULE

A schedule of recommended maintenance tasks and their frequency.

GENERAL RECOMMENDATIONS

General advice and requirements for proper unit upkeep.

CHECK FOR LOOSE FASTENERS AND PARTS

Procedure for inspecting the unit for loose or missing components.

CHECK FOR DAMAGED OR WORN PARTS

How to identify and address damaged or worn parts on the unit.

INSPECT AND CLEAN UNIT AND LABELS

Steps for cleaning the unit and its labels after each use.

CLEAN AIR FILTER

Instructions for cleaning the air filter to maintain performance.

REPLACE SPARK PLUG

Guide for replacing the spark plug for optimal engine starting.

SERVICE AND ADJUSTMENTS

REPLACING THE LINE

Step-by-step instructions for replacing the trimmer line spool.

BLADE REPLACEMENT

Reference to assembly section for blade replacement guidance.

CARBURETOR ADJUSTMENT

Procedure for adjusting the carburetor for optimal engine performance.

Idle Speed Adjustment

Specific steps to adjust the engine's idle speed correctly.

STORAGE

SEASONAL STORAGE

Preparation steps for storing the unit during off-season periods.

FUEL SYSTEM

Important considerations for the fuel system before storage.

ENGINE

Specific engine preparation procedures for storage.

TROUBLESHOOTING TABLE

EMISSION CONTROL WARRANTY STATEMENT