EasyManua.ls Logo

Craftsman CMXGTAMD25SC - User Manual

Craftsman CMXGTAMD25SC
48 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
769-16350 / 01 01/19
ELECTRIC START CAPABLE 2-CYCLE GAS TRIMMERS
DESBROZADORAS DE GAS DE 2 TIEMPOS CON CAPACIDAD PARA ARRANQUE ELÉCTRICO
OPERATOR’S MANUAL | MANUAL DEL OPERADOR
CMXGTAMD25CC & CMXGTAMD25SC
1-888-331-4569 WWW.CRAFTSMAN.COM
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

Table of Contents

Questions and Answers

  • D
    daughertyjenniferAug 10, 2025
    Why my Craftsman CMXGTAMD25SC engine will not start?
    • B
      Bradley StevensAug 10, 2025
      If your Craftsman Trimmer engine won't start, several factors could be at play. First, ensure the fuel tank isn't empty; if it is, fill it with properly mixed fuel. If the tank is full, try pressing the primer bulb 10 times, or until you see fuel. If the engine is flooded, move the choke lever to position 3, press the throttle lockout, squeeze the throttle control, and pull the starter rope until the engine starts. Old or improperly mixed fuel can also be a culprit, so drain the tank and refill with fresh fuel. Lastly, a fouled spark plug might be the issue, in which case you should replace it.
  • R
    Regina EatonAug 15, 2025
    What to do if the cutting head of my Craftsman Trimmer will not advance line?
    • R
      Richard BarnesAug 16, 2025
      If the cutting head on your Craftsman Trimmer isn't advancing the line, several issues could be responsible. Here's what to check: * The cutting head might be bound with grass: Stop the engine and clean the cutting head. * The cutting head could be out of line: Refill the cutting head with new line. * The inner reel might be bound up or the cutting head is dirty: Clean the inner reel and outer spool. * The line is welded: Open the cutting head and remove the welded section. * The line is twisted: Rewind the line. * Not enough line is extended: Stop the unit, push the bump knob, and pull the line until 4 inches (102 mm) is outside of the cutting head.
  • S
    Sharon JohnsonAug 22, 2025
    How to fix a Craftsman CMXGTAMD25SC Trimmer that will not idle?
    • M
      Mark StoneAug 22, 2025
      If your Craftsman Trimmer engine won't idle, here are a few things to check. First, a dirty air filter can cause idling problems, so clean or replace it. Also, old or improperly mixed fuel could be the issue; drain the fuel tank and add fresh, properly mixed fuel. Finally, the idle speed might be incorrect and require adjustment.
  • D
    Darius GloverAug 27, 2025
    Why does my Craftsman Trimmer engine lack power or stalls?
    • H
      Heather MezaAug 27, 2025
      If your Craftsman Trimmer engine lacks power or stalls, the issue might stem from several causes. Old or improperly mixed fuel is a common culprit; try draining the fuel tank and adding fresh, properly mixed fuel. A dirty air filter can also restrict engine performance, so clean or replace it. Lastly, a fouled spark plug could be the problem, requiring a replacement.
  • N
    Nicholas RiddleSep 2, 2025
    What to do if my Craftsman CMXGTAMD25SC engine will not accelerate?
    • T
      Timothy HallSep 2, 2025
      If your Craftsman Trimmer engine isn't accelerating, consider these potential issues: old or improperly mixed fuel might be the cause, so drain the fuel tank and add fresh, properly mixed fuel. Another possibility is that the cutting head is bound with grass; stop the engine and clean the cutting head. Finally, a dirty air filter can also prevent proper acceleration, so clean or replace it.

Summary

Important Safety Instructions

Assembly

Installing and Removing the Attachment

Oil and Fuel

Oil and Fuel Mixing Instructions

Guidance on correctly mixing gasoline and 2-cycle oil for the unit's engine.

Fueling the Unit

Steps and safety precautions for safely filling the fuel tank with the correct mixture.

Starting and Stopping

Starting Instructions

Step-by-step guide to safely start the engine using the manual starter mechanism.

Stopping Instructions

Procedure for safely turning off the engine and stopping the unit's operation.

Using the Electric Start Accessory

Starting Instructions

Operation

Holding the Unit

Proper posture, grip, and body positioning for safe operation of the trimmer.

Adjusting the Trimming Line Length (Bump Head)

Edging

Maintenance

Maintenance Schedule

Recommended service intervals and specific maintenance tasks for the unit.

Replacing the Trimming Line (Bump Head)

Replacing the Trimming Line (Fixed-Line Cutting Head)

Maintaining the Air Filter

Instructions for cleaning and re-oiling the air filter for optimal engine performance.

Adjusting the Idle Speed

Maintaining the Spark Plug

Cleaning and Storage

Cleaning

Storage

Guidelines for storing the unit for short or long periods, including fuel removal and securing.

Troubleshooting

Warranty

Limited Warranty

Overview of the manufacturer's limited warranty terms and coverage for the product.

Scope of the Limited Warranty

Defects in Workmanship or Materials

What This Limited Warranty Does Not Cover

This Warranty Does Not Cover and MTD LLC Disclaims Any Responsibility For

Limitations

Craftsman CMXGTAMD25SC Specifications

General IconGeneral
Engine Type2-Cycle
Engine Displacement25 cc
Fuel Mix Ratio40:1
Line Diameter0.095 in
Shaft TypeStraight
Attachment CapableNo
Power SourceGas
Handle TypeLoop

Related product manuals