Craftsman SECURITY+ 139.53682

To Next Page

CRRFTSMRN ®

OWNER'S MANUAL

Children operating or playing with s garage door

opener can injure themselves or others. The

garage door could close and cause serious injury

or death.

Install the receiver (or any additional push

buttons) out of the reach of children and away

from all moving parts of the door and door

hardware, but where the garage door is visible.

Do not allow children to operate the push

button(s) or the remote control(s).

A moving garage door could injure someone

under it. Activate the opener only when the door

is properly adjusted, you can see it clearly, and

there are no obstructions to door travel•

DISCONNECT POWER TO THE GARAGE DOOR

OPENER REFOREPROCEEDING.

The SECURITY+ Universal Remote Control

Conversion Kit consistsof a receiver and remote

control(s). This accessory will convert almost any garage

door opener to rollingcode technology. The remote control

sends a coded signal from outside the garage. Inside the

garage, the plug-inreceiver accepts the transmittedsignal

and starts the door opener. With Security+, the code

between the remote control and the receiver changes with

each use, accessing over 100 billion new codes.

IMPORTANT: To improve the security of your opener,

discard your old remote controls end erase or reset

your code. For maximum security and range, you

must disable the existing receiver on your opener,

otherwise it could still activate your opener:

• If there is an external receiver, disconnect power to it.

• If it is an integrated receiver, either clip off the

component that feeds power to the receiver or

remove the tuning slug and antenna from the receiver

section. If you have a different brand of opener,

contact the manufacturer for additional information on

disabling the existing receiver.

• If you have a Sears opener with an SRT receiver,

erase the old codes by holding down the SRT button

for 6 seconds until the indicator light turns off.

• If you have code switches, reset them to a random

code and deactivate the receiver as follows: On the

opener panel, peel

back the lower right _ I_ I_

corner of the label to

expose the tuning

slug (closest tothe

antenna), as shown.

Remove the slug

with a small hex

head wrench and cut

the antenna wire.

Cut

Antenna

Tuning

-- Slug

.Peal beck label

at comet

SECURITY,F

Universal Remote Control

Conversion Kit

Model 139.53682 (With I Remote Control)

Model 139.53683 (With 2 Remote Controls)

To complywithFco rules,adjustmentsor modificationsof thr= reseivorand,/or

transmitterare prohibited,except for changingthe code set_g o_replacing

the ransmittorbattery.THERE ARE NO USER SERV CEABLE PARTS.

NOTICE TO U. S. CONSUMERS:

Some stat_sprohibitthe service or repairof garage dooropeners

wbchcannotbe madeto complywiththe safetystandardscontained

in UL325 (1988 revision).In ordertocomplywithboththeletterand

the spiritof these laws, this universalremote conttolconverterkit

shouldnotbe usedwith anySears Craftsman=garage dooropener

manufacturedpdorto Apdl1, 1982.

Power..

Aotuator Cover Indicator

Light

SRT ._

Indicator

ght

Antenna

!Terminals

"o _11 Wire

- Illico..- _ act Bell Wire

L._ to Garage Door

•"_-- Opener Terminals

SRT (learn)

Actuator Belllwira

OPEN RECEIVER: Insert a small screwdriver in slot on

receiver front panel as shown• Twist up actuator cover.

CONNECT RECEIVER AND OPENER: Remove about

1/4" of insulation from each end of the 2-strand bell wire.

Connect one end to the receiver screw terminals

(polarity is NOT required). Route wire along the

channels and out the bottom as shown.

Connect the other end of the bell wire to the two opener

terminal screws labeled "2" (white) and "1" (red),

"common" and "command" or the terminals used for the

push button control.

Use insulated staples (not supplied) to secure bell wire

between receiver and opener. Length of bell wire

depends on where the receiver will be installed. Replace

the actuator cover.

Choose a 120Vac polarized outlet for the receiver which

is OUT OF THE REACH OF CHILDREN. Plug receiver

into selected outlet. Return power to the opener.

Side two contains code setting instructions and service

information,

Need help?

Do you have a question about the Craftsman SECURITY+ 139.53682 and is the answer not in the manual?

Summary

Safety and Warnings

General Garage Door Opener Safety

Crucial safety advice for operating garage doors to prevent injury or death from moving parts.

Child Safety Precautions

Instructions to keep openers and controls away from children to prevent misuse.

Installation and Setup

Product Introduction

Explains the SECURITY+ Universal Remote Control Conversion Kit and its rolling code technology.

Disabling Existing Receiver

Essential steps to disable the old receiver for enhanced security and optimal range.

Connecting Receiver to Opener

Detailed instructions for wiring the new receiver to the garage door opener terminals.

Receiver Outlet Placement

Guidance on selecting a suitable outlet for the receiver, prioritizing child safety.

Programming and Operation

Adding New Remote Controls

Step-by-step guide to program additional SECURITY+ remote controls to the receiver.

Erasing All Remote Codes

Procedure to clear all previously learned remote control codes from the receiver's memory.

Remote Control and Parts

Remote Control Battery Replacement

Instructions on how to safely open the remote and replace the lithium battery.

Replacement Parts Information

List of available replacement parts and contact details for ordering or repairs.