To Next PageTo Next PageHow to fix uneven cut from Craftsman T1200 247.203722?
If your Craftsman Lawn Mower is producing an uneven cut, several factors could be responsible. Begin by checking if the deck is leveled properly and perform a side-to-side deck adjustment if necessary. Ensure that the blade is sharp; if it's dull, sharpen or replace it. Lastly, verify that the tire pressure is even across all four tires.
What should I do if my Craftsman Lawn Mower engine hesitates at high RPM?
To address hesitation at high RPM in your Craftsman Lawn Mower engine, start by removing the spark plug and resetting the gap, as a gap that is too close can cause this issue.
What to do if my Craftsman Lawn Mower engine runs erratically?
If your Craftsman Lawn Mower engine is running erratically, there are several things you can check. First, ensure that the CHOKE is deactivated. Next, make sure the spark plug wires are securely connected. A blocked fuel line or stale fuel can also cause this issue, so replace the fuel line, fill the tank with clean, fresh gasoline, and replace the fuel filter. Additionally, a plugged vent in the gas cap could be the culprit; clear the vent or replace the cap if it's damaged. Water or dirt in the fuel system can also cause erratic running, so drain the fuel tank and refill with clean, fresh gasoline. Lastly, a dirty air cleaner can contribute to this problem, so replace the air cleaner paper element or clean the foam pre-cleaner if your mower is equipped with one.
Why is my Craftsman T1200 247.203722 Lawn Mower not mulching grass properly?
If your Craftsman Lawn Mower is not mulching grass effectively, there are several potential reasons. Ensure the engine speed is set high by placing the throttle in the FAST position. Avoid mulching when the grass is wet. If the grass is excessively high, mow once at a higher cutting height before mowing again at the desired height, or reduce the cutting swath. Finally, check if the blade is dull and sharpen or replace it as needed.
Why is my Craftsman Lawn Mower engine overheating?
If your Craftsman Lawn Mower engine is overheating, check the engine oil level and fill the crankcase with the correct amount and weight of oil. Also, ensure that the airflow is not restricted by cleaning any grass clippings and debris from around the engine’s cooling fins and housing.
What causes excessive vibration in my Craftsman Lawn Mower?
If your Craftsman Lawn Mower is experiencing excessive vibration, it may be due to a loose or unbalanced cutting blade. Tighten the blade and spindle to resolve this issue. Another potential cause is a damaged or bent cutting blade, which would require replacement.
Why does my Craftsman T1200 247.203722 engine idle rough?
If your Craftsman Lawn Mower engine idles roughly, it could be due to a spark plug issue. Replace the spark plug and set the plug gap. Also, a dirty air cleaner can cause rough idling, so replace the air cleaner element and/or clean the pre-cleaner.
Why won't my Craftsman T1200 247.203722 Lawn Mower engine start?
If your Craftsman Lawn Mower engine fails to start, several factors could be the cause. Ensure the PTO/Blade Engage lever is disengaged (OFF). Engage the parking brake. Check that the spark plug wires are connected, and the Throttle/Choke lever is in the FAST position. If the engine is still not starting, make sure that the choke is activated by moving the Throttle/Choke lever into the Choke position. Also, ensure the fuel tank isn't empty or filled with stale fuel; if so, fill it with fresh gasoline (less than 30 days old). Check for a blocked fuel line, replacing it and the fuel filter if necessary. Inspect the spark plug(s) for faults, cleaning, adjusting the gap, or replacing them as needed. If the engine is flooded, crank it with the throttle in the FAST position. Finally, check for b...
General| Engine Brand | Briggs & Stratton |
|---|---|
| Number of Blades | 2 |
| Warranty | 2-year limited |
| Cutting Width | 42 in |
| Cutting Height | 1.5-4 in |
| Rear Tire Size | 20x8-8 |
| Fuel Tank Capacity | 1.36 gallons |
| Front Tire Size | 15 x 6 inches |
