EasyManua.ls Logo

CRAM-A-LOT VB-60-X - User Manual

Default Icon
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
“Equipping The World For A Better Environment”
MODELS
VB-42-B
VB-42-B-LP
VB-60-B
VB-60-B-LP
VB-60-T
VB-60-H
VB-60-X
VB-60-H-DC
VB-60-H-LP
VB-72-B
VB-72-B-LP
VB-72-T
VB-72-H
VB-72-X
VB-72-H-DC
VB-72-H-LP
Operation, Maintenance, and Installation
OWNER / OPERATOR INSTRUCTION MANUAL

Table of Contents

Questions and Answers

  • I
    imooreAug 17, 2025
    What to do if the motor won’t start when I turn the key on my CRAM-A-LOT Lawn and Garden Equipment?
    • T
      Travis UnderwoodAug 17, 2025
      If the motor of your CRAM-A-LOT Lawn and Garden Equipment won’t start when you turn the key, take these steps: * Make sure the emergency stop switch is not engaged. * If the baler is in “Auto” or “Manual Down” mode, make sure the loading door is fully closed. * If the baler is in “Manual Up” mode, make sure the loading door is open. * Make sure the electromagnetic door latch and striker surfaces are clean. * Make sure the disconnect or circuit breaker is turned on.
  • M
    Mrs. Kimberly HallAug 21, 2025
    What to do if the motor runs but the presshead won’t move on my CRAM-A-LOT VB-60-X Lawn and Garden Equipment?
    • J
      jenniferbyrdAug 21, 2025
      If the motor runs but the presshead won’t move on your CRAM-A-LOT Lawn and Garden Equipment, consider the following: * In “Manual Up” mode, you need to pull out the emergency stop switch to raise the presshead. * Ensure that the loading door is fully closed. * Ensure that the electromagnetic door latch and striker surfaces are clean. * Ensure that the chamber door is fully closed.
  • K
    Kelly SheltonAug 25, 2025
    Why does my CRAM-A-LOT Lawn and Garden Equipment stop when I release the key?
    • R
      Robert BaileyAug 25, 2025
      If your CRAM-A-LOT Lawn and Garden Equipment stops when you release the key, it could be due to the upper magnetic interlock switch failing “OPEN”. To address this: * Close and latch the loading door. * Check the upper magnetic interlock switch for proper alignment to the magnet on the loading door. * Check the upper magnetic interlock switch. * Replace the upper magnetic interlock switch if necessary.
  • C
    Cynthia EllisonAug 27, 2025
    What to do if the loading door won’t stay closed on my CRAM-A-LOT VB-60-X?
    • D
      Dawn ArnoldAug 27, 2025
      If the loading door won’t stay closed on your CRAM-A-LOT Lawn and Garden Equipment, check these: * Make sure the key is turned to the “On” position. * Make sure the emergency stop switch is not engaged. * Make sure the mode selector switch is in the “Auto” or “Man Down” positions. * Make sure the electromagnetic door latch and striker surfaces are clean. * Make sure the chamber door is fully closed.
  • A
    Amy CamposAug 30, 2025
    What to do if the ram retracts to the top, the Baler continues to run on my CRAM-A-LOT VB-60-X Lawn and Garden Equipment?
    • W
      wileyjerryAug 30, 2025
      If, when the ram retracts to the top, the baler continues to run on your CRAM-A-LOT Lawn and Garden Equipment, it could be caused by the upper magnetic interlock switch failing “CLOSED”. Check the upper magnetic interlock switch mounting bracket for proper operation and check the upper magnetic interlock switch. Replace the upper magnetic interlock switch if needed.
  • S
    Stephanie LindseySep 3, 2025
    How to open the loading door on my CRAM-A-LOT VB-60-X to load material?
    • K
      kennethgutierrezSep 3, 2025
      To open the loading door on your CRAM-A-LOT Lawn and Garden Equipment so material can be loaded, turn the key to the “Off” position. The loading door should raise automatically.
  • C
    Christopher NicholsSep 6, 2025
    Why won’t the bale eject from my CRAM-A-LOT VB-60-X Lawn and Garden Equipment?
    • M
      martha87Sep 7, 2025
      If the bale won’t eject from your CRAM-A-LOT Lawn and Garden Equipment, make sure that the dump handle was engaged before the machine was operated in the “Manual Up” mode to dump the bale. Also, on newer balers, the paint on the inside of the bale chamber may prevent the bale from ejecting well. While ejecting the bale the motor may shut off. If this occurs, the baler cycle timer has timed out.
  • E
    Eddie SandovalSep 10, 2025
    Why won’t the bale ties go through the slots in my CRAM-A-LOT VB-60-X Lawn and Garden Equipment?
    • M
      Megan JeffersonSep 10, 2025
      If the bale ties won’t go through the slots in the floor or presshead of your CRAM-A-LOT Lawn and Garden Equipment, make sure the chamber door is open. Also, ensure that the correct end of the bale tie is being guided through the slots. Before making the bale, ensure that a full sheet of cardboard has been laid on the chamber floor. Before the presshead was lowered, ensure that a full sheet of cardboard has been laid on top of the full bale.
  • M
    Michael ParkerNov 13, 2025
    Why won't my CRAM-A-LOT Lawn and Garden Equipment baler start?
    • K
      Kristi JohnsonNov 13, 2025
      The baler might not start due to several reasons: * The stop button may be in the “STOP” position. To resolve this, pull the STOP button out to the “RUN” position. * The electromagnetic lock may have failed “OPEN”. In that case, close and latch the loading door. Also, check the door position sensor for proper alignment to the magnet on the door strike plate, check the electromagnetic lock, and if needed, replace the electromagnetic lock. * The electromagnetic lock may have failed “CLOSED”. To fix this, cycle power to unlock the loading door. Also, close and latch the loading door, check the door position sensor for proper alignment to the magnet on the door strike plate, check the electromagnetic lock, and if needed, replace the electromagnetic lock. * The motor starter may have f...

Summary

Baler Operation

Safety Orientation

Key safety precautions and terminology for safe operation.

Location of Baler Controls

Identification of key control switches and buttons on the baler.

Emergency Procedures

Steps to take during an emergency shutdown.

Standard Baler Operation

Step-by-step guide for normal baler operation.

Making and Tying a Bale

Process for creating and securing a bale.

Ejecting a Bale

Procedure for safely removing the finished bale from the chamber.

Maintenance

Lock Out; Tag Out Procedures

Steps to isolate hazardous energy before servicing.

Chocking the Presshead

Preventive Maintenance Schedule

Checking and Adding Oil

Troubleshooting

Motor Wont Start

Common issues when the motor fails to start.

Motor Runs But Presshead Wont Move

Troubleshooting when the motor runs but the presshead is immobile.

Loading Door Wont Open

Loading Door Wont Stay Closed

Bale Wont Eject

CRAM-A-LOT VB-60-X Specifications

General IconGeneral
BrandCRAM-A-LOT
ModelVB-60-X
CategoryLawn and Garden Equipment
LanguageEnglish

Related product manuals